Page 1
ORDER No.MD0007129C3 DVD Stereo System SA-PM08 Colour (S) ....Silver Type Areas (GCS) .... Asia (GK) ....China CD SECTION : DPT-4AT-AD TRAVERSE DECK SERIES SYSTEM : SC-PM08 SPECIFICATIONS Specifications...
AMPLIFIER SECTION Front speaker power output RMS power output THD 10%, both channels driven Front (HIGH) 10W per channel (6 Front (LOW) 10W per channel (6 20W per channel Total bi-amp power Power output in SSS mode RMS power output THD 10%, both channels driven Front (HIGH) 10W per channel (6...
*1 Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are trademarks ofDolby Laboratories. SYSTEM SC-PM08 : / Main unit : SA-PM08 / Front speakers : SB-PM08 / Surround speakers : SB-PS80 / Center Speakers : SB-PC80 1.
instance), as this may destroy solid state devices. / After repairsare completed, restore power gradually using a variac, to avoid overcurrent. / Current consumption at AC230V, 50Hz in NO SIGNAL mode should be less than 300mA. 2. Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: - No sound is heard when the power is turned on.
Page 5
2. In order to prevent static electricity damage to the laser diode, use a short pin or similar tool to short the optical pickup’s flexible circuit boards after they have been disconnected from the main circuit board. 3. Handle the flexible circuit boards with care; excessive force could cause them to be broken.
Caution: The static electricity of your clothes will not be grounded through the wrist strap. / So, take care not to let your clothes touch the traverse deck (optical pickup) 4.3. Caution when Replacing the Traverse Deck The traverse deck has a short point shorted with solder protect the laser diode against electrostatic breakbown.
Page 7
6. Location of Controls 7. Location of Controls for Remote Control...
Transmitter 8. Operation Checks and Component Replacement Procedures - This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. - For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required.
Page 9
- Check the main P.C.B., power supply P.C.B. and system control P.C.B. (A side) as shown below.
Page 10
- Check the system control P.C.B. (B side) as shown below. 8.2. Checking for the DVD module (1) P.C.B. and mic echo P.C.B. - Follow the (Step 1) - (Step 12) of item 8.1.
Page 11
- Check the DVD module (1) P.C.B. (A side) and mic echo P.C.B. as shown below.
Page 12
- Check the DVD module (1) P.C.B. (B side) as shown below. 8.3. Checking for the DVD module (2) P.C.B. - Follow the (Step 1) - (Step 12) of item 8.1. - Follow the (Step 1) - (Step 3) of item 8.2. - Check the DVD module (2) P.C.B.
Page 13
8.4. Checking for the power AMP P.C.B. - Follow the (Step 1) - (Step 3) of item 8.1. - Check the power AMP P.C.B. as shown below.
Page 14
8.5. Replacement for the traverse deck ass’y - Follow the (Step 1) - (Step 11) of item 8.1. - Follow the (Step 1) - (Step 3) of item 8.2.
Page 16
8.6. Replacement for the traverse motor ass’y, optical pickup and spindle motor ass’y...
Page 17
- Follow the (Step 1) - (Step 11) of item 8.1. - Follow the (Step 1) - (Step 3) of item 8.2. - Follow the (Step 1) - (Step 14) of item 8.5.
Page 20
8.7. Replacement for the belt, loading motor ass’y and loading switch - Follow the (Step 1) - (Step 11) of item 8.1. - Follow the (Step 1) - (Step 3) of item 8.2. - Follow the (Step 1) - (Step 11) of item 8.5.
Page 21
8.8. Replacement for the lamp ass’y, shutter panel and rack - Follow the (Step 1) - (Step 11) of item 8.1. - Follow the (Step 1) - (Step 3) of item 8.2.
Page 24
8.9. Replacement for the transfer gear (A)/(B), belt, pulley and motor - Follow the (Step 1) - (Step 11) of item 8.1. - Follow the (Step 1) - (Step 3) of item 8.2. - Follow the (Step 1) , (Step 2) of item 8.8.
Page 25
8.10. Replacement for the power IC - Follow the (Step 1) - (Step 3) of item 8.1. - Follow the (Step 1) - (Step 3) of item 8.4.
Page 27
9. Illustration of ICs, Transistors and Diodes 10. Schematic Diagram 10.1. Schematic Diagram Notes - This schematic diagram may be modified at any time with the development of new technology. Notes:...
Page 29
not touch the legs of ICor LSI with the fingers directly. - Voltage and signal line / : Positive voltage line / Negative voltage line / : Video/audio signal line / Video signal line / : Audio signal line / : FM signal line / : FM OSC signal line /...
Page 30
Function Terminal Name DISC DVD/CD tray close switch CLS SW 24 VERF+ — A/D converter reference voltage 25 DCMD DVD data out (command out) 26 DSTAT DVD data in (status in) 27 DCLK DVD clock input — N.C. DISC DVD/CD tray open DISC DVD/CD tray close 31 CRTIMER I/O...
Function Terminal Name 18dB 18db attenuator/EEPROM clock EEPROM chip select output signal 56 WIDE2 DVD control output signal 57 WIDE1 DVD control output signal Display close control output signal Display open control output signal 60 ECHO Echo data output signal 61 ECHO Echo clock output signal 62 EHCO...
Page 32
Ref. No. Part No. Part Name & Description Pcs. Remarks CABINET AND CHASSIS RGP0794A-A ORNAMENT PANEL 1 [M] RKM0415A-S FRONT PANEL 1 [M] RGP0793-Q LCD PANEL 1 [M] RGU1883-H VOLUME BASE 1 [M] RGU1871-S VOLUME BUTTON 1 [M] RGU1869-S1 OPERATION BUTTON 1 [M] RGU1870-S1 EJECT BUTTON...
Page 33
Ref. No. Part No. Part Name & Description Pcs. Remarks REE0999 MICON PAB PANEL PCB 2 [M] REE1003 DVD MODLE - AUDIO PC 1 [M] REE1004 DVD MODLE - AUDIO PC 1 [M] REE1001-1 DVD MODULE - DVD F.E 1 [M] REE1002 DVD MODULE - DVD F.E 1 [M]...
Page 34
Ref. No. Part No. Part Name & Description Pcs. Remarks BML3E4CRU SPINDLE MOTOR VEM0720 SPINDLE MOTOR UNIT VMB3278 TILT SPRING VMC1487 SUB-SHAFT SPRING VMC1606 SPRING HOLDER 1 VMC1607 SPRING HOLDER 2 VMG1166 FLOATING RUBBER VMK0502 TRAVERSE CHASSIS VMS6471 GUIDE SHAFT 1 VMS6472 GUIDE SHAFT 2 VED0402-1...
Page 35
Ref. No. Part No. Part Name & Description Pcs. Remarks IC3061 KM416S1DTG8T IC S-DRAM 16M 1 [M] IC3071 KM416S1DTG8T IC S-DRAM 16M 1 [M] IC3091 PQ1R33 IC REGULATOR IC3501 BA7665FS-E2 IC VIDEO AMP 1 [M] IC4202 PCM1600Y1T2 IC 6CH A-DAC 1 [M] IC4203 MM1385ENRE...
Page 45
Ref. No. Part No. Part Name & Description Pcs. Remarks JK102 RJH8203N JK VIDEO 1 [M] JK103 RJH2110N-2 JK SUB-WOOFER 1 [M] JK650 RJJ37TK07-X JK MIC 1 [M] JK651 RJJ37TK07-X JK HP 1 [M] JK801 SJS9236-J JK AC INLET JK901 RJH5603-4 JK SPEAKER TERMINAL 1 [M]...
Page 79
Note) : VIDEO/AUDIO SIGNAL LINE PQ018EZ01ZP UPC29M33T : VIDEO SIGNAL LINE IC3002 IC6251 : AUDIO SIGNAL LINE REGULATOR D+2.5V REGULATOR D+5V : SUB WOOFER SIGNAL LINE : CENTER SP. SIGNAL LINE : SURROUND SP. SIGNAL LINE D IN1 (To MAIN SECTION) D IN2 VOUT6 D IN3...
MAIN SECTION Z101 TUNER UNIT FM ANT AM ANT +B(FM) RF AMP FM MIXER COIL COIL +B(FM) FM IF +B(FM) BUFFER LOCAL OSC +B(FM) LA1833NM FM / AM I F AMP, DET / AM OSC, MIX / FM MPX DECODER BUFF.
SCHEMATIC DIAGRAM-1 DVD MODULE(2) CIRCUIT Note: The number which noted at the connectors on the schematic diagram as "SCHEMATIC DIAGRAM-1" or "SCHEMATIC DIAGRAM-2" indicates the schematic diagram serial number located on the left corner in the schematic diagram. : POSITIVE VOLTAGE LINE : VIDEO / AUDIO SIGNAL LINE OPTICAL PICKUP UNIT LB5201...
Page 103
SCHEMATIC DIAGRAM-7 DVD MODULE(1) CIRCUIT : POSITIVE VOLTAGE LINE : VIDEO / AUDIO SIGNAL LINE RA7003 1.2V HDD15 SBCK 3.3V HDD0 PLAY HDD14 3.5V PLAY 3.3V 3.3V 3.5V 3.3V 3.3V HDD1 3.3V HDD13 0.36 3.3V HDD2 PLAY ODCO1 1.7V 1.3V 2.6V HDD12 ODCI1...
Page 105
SCHEMATIC DIAGRAM-9 : POSITIVE VOLTAGE LINE : VIDEO SIGNAL LINE DVD MODULE(1) CIRCUIT : VIDEO / AUDIO SIGNAL LINE : AUDIO SIGNAL LINE C3010 C3013 C3002 6.3V330 C3003 6.3V330 3.3V 3.3V 1.3V 1.3V 1.1V 3.3V 1.3V 1.8V TEST9 3.3V XRST VCLK 3.3V TEST8...
SCHEMATIC DIAGRAM-11 :POSITIVE VOLTAGE LINE :AUDIO SIGNAL LINE :CENTER SP. DRIVE SIGNAL LINE DVD MODULE(1) CIRCUIT :VIDEO SIGNAL LINE :SURROUND SP. DRIVE SIGNAL LINE :SUB WOOFER SIGNAL LINE R4202 R4203 FP4201 LB4020 A.GND LB4019 R4204 A.GND LB4018 2.5V A GND V OUT3 2.5V R4205...
SCHEMATIC DIAGRAM-12 OPERATION CIRCUIT :POSITIVE VOLTAGE LINE LCD601(RSL5259-G) LCD DISPLAY Z601 RCDRPM6937V4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 (REMOTE SENSOR) W X Y Z a b d e f g h i j m n p q r...
Page 109
SCHEMATIC DIAGRAM-13 SYSTEM CONTROL CIRCUIT :POSITIVE VOLTAGE LINE r q p n m j i h g f e d b a Z Y X W V U T S R R514 X501 X502 (8MHz) (32kHz) 2.5V 2.6V COM3 SEG25 4.8V 2.5V 2.6V...
Page 110
SCHEMATIC DIAGRAM-14 :POSITIVE VOLTAGE LINE R537 R573 4.7K CN103B +B(15V) LINE IUT MUTE PLL DO/ ST PLL CE SSS DET PLL CLK/ A CLK PLL DI/ A DATA R541 A LATCH +B(5V) MUTE B MAIN LFE MUTE CIRCUIT R536 18dB ECLK (CN103A) on SCHEMATIC VREF-...
Page 111
SCHEMATIC DIAGRAM-15 MIC AMP CIRCUIT Q450 2SC2712GRT5T SWITCHING 0.9V C459 R458 100P IC450 M65853FPE1 R457 DIGITAL ECHO/ MIC MIXING 2.5V 0.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 1.2V 0.9V 1/ 2Vcc A/ D MCLK MAIN LOGIC MIC SW 16Kbit...
Page 112
SCHEMATIC DIAGRAM-16 SYSTEM CONTROL CIRCUIT(CN103B) on SCHEMATIC DIAGRAM-14 :POSITIVE VOLTAGE LINE :NEGATIVE VOLTAGE LINE :SURROUND SP. DRIVE SIGNAL LINE :CENTER SP. DRIVE SIGNAL LINE :SUB WOOFER SIGNAL LINE :AUDIO SIGNAL LINE :VIDEO SIGNAL LINE 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 CN103A CN101 A.GND...
Page 113
SCHEMATIC DIAGRAM-17 :POSITIVE VOLTAGE LINE :AUDIO SIGNAL LINE :CENTER SP. DRIVE SIGNAL LINE MAIN CIRCUIT :NEGATIVE VOLTAGE LINE :SURROUND SP. DRIVE SIGNAL LINE :SUB WOOFER SIGNAL LINE 5.2V -7.7V R230 R274 2.2K R183 100K R234 C187 C208 1000P 5.2V 5.1V 5.1V 5.1V R233...
Page 114
SCHEMATIC DIAGRAM-18 :AUDIO SIGNAL LINE :SURROUND SP. DRIVE SIGNAL LINE :POSITIVE VOLTAGE LINE :FM SIGNAL LINE :CENTER SP. DRIVE SIGNAL LINE :NEGATIVE VOLTAGE LINE :AM SIGNAL LINE :SUB WOOFER SIGNAL LINE 5.2V IC108 C101 C108 3300P 3300P TC4052BFNELM SIGNAL SELECTOR R408 R404 5.2V...
Page 115
SCHEMATIC DIAGRAM-19 :SURROUND SP. DRIVE SIGNAL LINE :POSITIVE VOLTAGE LINE :AUDIO SIGNAL LINE :FM SIGNAL LINE :CENTER SP. DRIVE SIGNAL LINE MAIN CIRCUIT :NEGATIVE VOLTAGE LINE :VIDEO SIGNAL LINE :AM SIGNAL LINE :SUB WOOFER SIGNAL LINE D118 T0TX178A L101 OPT. 5.2V DIGITAL OUT Q129-134...
SCHEMATIC DIAGRAM-20 :POSITIVE VOLTAGE LINE :NEGATIVE VOLTAGE LINE FAN MOTOR :AUDIO SIGNAL LINE :SURROUND SP. DRIVE SIGNAL LINE POWER AMP CIRCUIT :CENTER SP. DRIVE SIGNAL LINE CN750 Q750-752 2SC2712GRT5T R752 MOTOR DRIVE 820K Q753 2SB621ARTA MOTOR DRIVE Q750 Q752 C751 R756 Q510 Q509...
Page 117
SCHEMATIC DIAGRAM-21 :AUDIO SIGNAL LINE :POSITIVE VOLTAGE LINE :SURROUND SP. DRIVE SIGNAL LINE :NEGATIVE VOLTAGE LINE :CENTER SP. DRIVE SIGNAL LINE IC901 TA8255AH POWER AMP For [GK] area. L948-961 SPEAKERS ZBF506D-00TA JK901 SURROUND L948 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 L949 R970 L950...
Page 120
SCHEMATIC DIAGRAM-24 For [GK] area. :FM SIGNAL LINE :AM SIGNAL LINE Z101 TUNER UNIT(RAN0005EM-1) :POSITIVE VOLTAGE LINE :FM OSC SIGNAL LINE :AM OSC SIGNAL LINE 2SC2059 FM MIXER 2SK360 6 ~ 220 RF AMP FM ANT (75 ) 0 ~ 220 2SK360 FM OSC 2SC2413...
Page 121
SCHEMATIC DIAGRAM-25 :FM SIGNAL LINE :FM/ AM SIGNAL LINE :POSITIVE VOLTAGE LINE :AM SIGNAL LINE :AM OSC SIGNAL LINE 10P ~ 270K ~ 270K ~ 680K 680K 1000P 2SC2413 2SC2413 FM IF AMP FM IF AMP DTA114 POWER SUPPLY (FM:ON) LA1833MN FM/AM IF AMP, DET/AM OSC,MIX/FM MPX...
Page 122
SCHEMATIC DIAGRAM-26 For [GCS] area. :FM SIGNAL LINE :AM SIGNAL LINE Z101 TUNER UNIT(RAN0004MM-1) :POSITIVE VOLTAGE LINE :FM OSC SIGNAL LINE :AM OSC SIGNAL LINE 2SC2059 FM MIXER 2SK360 0 ~ 220 RF AMP FM ANT 2SC2413 BUFFER AMP AM ANT 0.47 LOOP 330P ~...
Page 123
SCHEMATIC DIAGRAM-27 :POSITIVE VOLTAGE LINE :FM SIGNAL LINE :AM SIGNAL LINE :AM OSC SIGNAL LINE 270K ~ 270K ~ 680K 1000P 680K 1000P 2SC2413 2SC2413 FM IF AMP FM IF AMP DTA114 POWER SUPPLY (FM:ON) LA1833NM FM/AM IF AMP, DET/AM OSC,MIX/FM MPX 6.8K 6.8K 0.47...
DVD MODULE (1) P.C.B. TRAVERSE FP6101 FP3501 12 ..1 15 ... . . 1 MOTOR UNIT 20 . FP4201 26 . FP7101 BLUE BLACK...
Page 126
SPEAKERS BLACK FAN MOTOR CN750 CN901B 10 . POWER AMP P.C.B. LOADING MOTOR (DISC TRAY) P.C.B. CN902B BLUE BLACK CN903 CP790 10 . OPERATION P.C.B. CN602B CN601B 2 ... 26 2 .