Table of Contents
Advertisement
COPYING A VIDEO TAPE
You can make copies of video tapes made by friends or
relatives for your enjoyment.
You can not copy a DVD to a videotape.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording VCR (this unit), the playing
VCR (another source) and your TV using the follow-
ing diagram.
¡
You can use the AUDIO/VIDEO input jacks on the
front panel of the DVD/VCR instead of using the
jacks on the back.
[Recording VCR]
(this unit)
RF cable
(supplied)
Audio/Video cables
[TV set]
(Use for monitoring)
ANT in
1
Insert a pre-recorded tape into the playing VCR.
2
Insert a tape with a safety tab into the
recording VCR.
3
Press SPEED on the recording VCR to select the
desired recording speed (SP/SLP).
4
Select the "L1" or "L2"position on the
recording VCR.
¡
When you use the A/V input jacks on the back of the
DVD/VCR, select "L1" position by pressing [0], [0], [1]
on the remote control or the CHANNEL (o/p) buttons.
¡
When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0], [2]
on the remote control or the CHANNEL (o/p) buttons .
5
Press REC/OTR on the recording VCR.
6
Begin playback of the tape in the playing
VCR.
¡
For best results during dubbing, use the VCR's front
panel controls whenever possible. The remote con-
trol might affect the playing VCR's operation.
¡
Always use video-quality shielded cables with
RCA-type connectors. Standard audio cables are not
recommended.
¡
You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in
place of the playing VCR.
SPECIAL FEATURES
VCR
(not supplied)
OUT
IN
LEFT
AUDIO
RIGHT
VIDEO
[Playing VCR]
(another source)
TO MONITOR THE RECORDING
1
Turn on the TV and set the TV to channel 3.
¡
If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4)
on
your
CHANNEL" on page 13 for the detail).
2
Press VCR/TV on the recording VCR.
MTS (Multi-Channel Television
Sound) SYSTEM
When you play a VHS tape, or receive a broadcast on
the VCR's tuner, the current sta-
tus will appear when you press
DISPLAY on the remote control.
When you record a MTS broad-
cast signal, you need to set it to
MTS mode.
1)*
Press MENU and select "TV STEREO" or
"SAP" by pressing K or L. Then, press B
to select mode. To exit, press
CLEAR/C.RESET.
¡
Although a program may be broadcast in both stereo
and sub audio, you must select the Recording mode
to TV STEREO or SAP before you record a broad-
cast.
2)*
Press MENU and select "AUDIO OUT" by
pressing K or L. Then, press B. Next,
select "HIFI" or "MONO" by pressing K or
L. To exit, press CLEAR/C.RESET.
¡
While the VCR is set in HIFI stereo mode, HIFI
appears on the TV screen. While the VCR is set in
monaural (MONO) mode, HIFI disappears from the
TV screen.
MTS RECORDING/MONITOR MODE
Display on the
Type of
broadcast
TV screen
Regular
-None-
(monaural audio)
Stereo
STEREO
broadcast
SAP
Bilingual
broadcast
Stereo &
STEREO
Bilingual
SAP
broadcast
*
– 21 –
TV.
(See "RF
STOP
SP
0:00:00
STEREO/SAP
Hi-Fi audio track
Selection
(2-channel)
L-channel
R-channel
-Invalid-
Mono
Mono
- nvalid-
I
L
R
Main audio
Main audio
TV STEREO*
program
program
Sub audio
Sub audio
SAP*
program
program
TV STEREO*
L
R
Sub audio
Sub audio
SAP*
program
program
OUTPUT
VCR
12:00AM
CH 32
STEREO
1)*
SAP
2)*
HIFI
Normal audi o
track
Mono
L+R
Main audio
program
Sub audio
program
L+R
Sub audio
program
EN
1L25
Advertisement
Table of Contents
