Advertisement
Quick Links
Manufactured by:
394 Dairy Pak Rd. • Athens, GA 30607
kdframes.com • alan@kdframes.com
P A R T S
L I S T
K-41
BACK RAIL
K-2
SEAT RAIL
K-15 20" SEAT SLAT CAPS
K-18 25" BACK SLAT CAPS
K-65
PROP CONNECTOR
K-6
BACK LEG (Left and Right)
K-7
SEAT LEG
K-10 SEAT SLAT SUPPORTS
K-18 BACK SLAT SUPPORTS
K-4
PROP
PARTS
(2) K-4 PROP - 15"
(2) K-15 SEAT SLAT CAP - 20"
(2) K-18 BACK SLAT CAP - 25"
(1) K-10 SEAT SLAT SUPPORT - 24"
(1) K-18 BACK SLAT SUPPORT - 29"
(2) K-7 SEAT LEG - 9"
Instructions for
Studio Bifold
Queen #7721
2
K-64 MIDDLE SLATS
2
K-61 BACK SLATS
2
K-62
SEAT SLATS
2
1
H-8
2-1/4" CLEVIS PIN
2
3" CLEVIS PIN
H- 12
H-5
2
HAIR PIN
H-6
1
WASHER
H-11 WOOD DOWEL
1
2
H-19 1-1/2" SCREW
(2) K-61 BACK SLAT - 76"
(2) K-62 SEAT SLAT - 76"
(7) K-64 MIDDLE SLAT - 72"
(1) K-65 PROP CONNECTOR - 60"
(2) K-2 SEAT RAIL - 37"
(2) K-41 BACK RAIL - 34"
K-6L BACK LEG (Left) (1)
K-6R BACK LEG (Right) (1)
1
v. 309
7
2
2
4
2
6
6
20
29
2
K-4
The Prop Connector (K-65)
shown above is shortened
Use a small hammer to tap
Wood Dowels (H-11) all the
way into holes as shown.
K-4 PROP (2)
K-41 BACK RAIL (2)
K-2 SEAT RAIL (2)
Press the Prop Connector (K-65)
onto the Wood Dowels on the
Props (K-4) and attach with
1-1/2" Screws (H-19).
H-19
K-65
K-4
NOTE:
to save space.
Advertisement
Summary of Contents for kd frames Studio Bifold Queen 7721
- Page 1 Instructions for Manufactured by: Use a small hammer to tap Studio Bifold Wood Dowels (H-11) all the way into holes as shown. 394 Dairy Pak Rd. • Athens, GA 30607 Queen #7721 kdframes.com • alan@kdframes.com v. 309 P A R T S L I S T K-41 BACK RAIL...
- Page 2 Attach the Left and Right Back Legs (K-6) to the Be sure that the Prop outside of the Back Rails using Connector goes below the 3” Cevis Pins (H-12). the Back Rails. Do not put on the Washers and Hair Pins at this time. H-12 K-6R K- 4 1...
- Page 3 Using (3) Middle Slats (K-64) K-1 5 Attach the Seat Legs (K-7) to the push the Wood Dowels Seat Rails using 2-1/4” Clevis Pins (H-8). into the edge holes on Secure with Washers (H-6) and Hair Pins (H-5). (2) Seat Slat Caps (K-15). K-6 4 Find the (2) Seat Slats (K-62) and push them onto the...
- Page 4 Operation: Attach the Seat Slat Support (K-10) under the Seat Deck and the Back Slat Support (K-18) under the Back Deck by screwing (4) Wood Screws (H-19) down through the Slats H-19 and into holes provided in the Slat Supports. Bed position: K-18 Sofa position:...