Related Manuals for Toa VX-1000MC-W
Summary of Contents for Toa VX-1000MC-W
- Page 1 User’s Manual Matrix Controller VX-1000MC-W Peering Frame VX-1000PF-W Digital Amplifier Module 125W VX-1125DA-W 250W VX-1250DA-W 500W VX-1500DA-W...
- Page 2 Thank you very much for purchasing TOA VX-1000 series product. Please read the instructions in this manual carefully, to ensure long-term, trouble-free operation of the system. TOA Corporation...
-
Page 3: Safety Precautions
1. SAFETY PRECAUTIONS Please abide by the warning and the relevant safety tips. Please take this manual in convenient place after you reading the guide for future reference. Warning The sign means there is potential safety hazard, when operate wrong may result in death or serious injury. - Page 4 the safe, please shut off power supply switch, and will power plug. If failure to comply with this provision, it will likely cause electric shock or fires.
-
Page 5: Product Introduction
2. PRODUCT INTRODUCTION 2.1 Overview Matrix controller can realize business broadcasting and fire alarm linkage emergency broadcasting by supporting Peering Frame and fire alarm. It is a Public Address system and fire protection linkage alarm system suitable for large public places such as railways, business offices, factories, schools, hospitals, shopping malls, entertainment places, etc. -
Page 6: Interface Description
(3) Modular design, small and light appearance. (4) It has a fault detection function, which can detect faults such as overcurrent, overheat, and fan abnormality, and displays them on the indicator light of the power supply chassis. 2.2 Interface Description 2.2.1 Matrix Controller Front Panel Handheld Microphone Interface: connect the handheld microphone (PM-100VX-EA) to this... -
Page 7: Audio Monitor
ACK Button: When the system detects a fault, press the "ACK" button to confirm the fault, the fault indicator orange light is always on, and the LCD screen displays specific fault information. Equipment status indicator, the relevant instructions are as follows: Status Indicator LED Introduction Two-color lights, orange light without power input, green light... - Page 8 ATT-CTR OUT: 4 channels attenuator control output. (NO: normally open, C: public, NC: normally closed) ANC-SENSOR IN: 4 microphone (as an ambient detection sensor) inputs, which can be connected to an ambient noise detector to automatically adjust the broadcast sound output level according to environmental noise level.
- Page 9 Line sequence and definition of control input / control output interface: Name Color Pair Description Assignment ① Orange/White COM 1 Common 1 ② Orange NO 1 Normally Open 1 ③ Green/White COM 2 Common 2 CTRL_OUT ④ Blue COM 3 Common 3 ⑤...
- Page 10 2.2.2 Peering Frame Front Panel Name Indicator light status Green light when there is power input, and does not light up when there AC POWER IN A is no power input. Green light when there is power input, and does not light up when there AC POWER IN B is no power input.
- Page 11 Rear Panel POWER Switch: control the power on and off. PA LINK: power amplifier interfaces (amplifier channels 1-4), respectively connected to the matrix controller's power amplifier interface 1-4; 1 channel for standby power amplifier interface, connected to the matrix controller's standby power amplifier STANDBY-PA LINK interface.
- Page 12 3. Wiring 3.1 Matrix Controller Wiring Diagram...
- Page 13 3.2 Digital Power Amplifier Module Installation Diagram Installation steps Step 1：Remove the four M3 * 10 countersunk screws on the panel of the Peering Frame, and then remove the panel. Step 2：Loosen the thumb screw (no need to completely unscrew it, the lock piece can be dropped to the lower right), and turn the lock piece to the lower right (hook down).
- Page 14 3.3 Reference Size（unit：mm） 3.3.1 Matrix Controller 3.3.2 Peering Frame...
- Page 15 4. Instructions 4.1 VX-1000 Configuration tool operating instructions 4.1.1 Software Installation Double-click the VX-1000 installer and press "Next" to install. After the installation is complete, select "Run as administrator" software. 4.1.2 Basic parameter settings (1) New project file ： Click "File"-"New" in the main interface of the software, enter the project name in the pop-up dialog box, and create a new project file.
- Page 16 (3) Matrix extended partition configuration: Set the number of matrix extended partition extenders vX-1010ZE-EA. If the vX-1010ZE-EA is not connected, then you do not need to set this parameter. A maximum of 16 partition extenders can be added.After the configurations are completed, the system will save configurations automatically.
- Page 17 (4) Device Configuration：After the device is added, the names of the input and output channels and control input and output channels of each matrix controller can be customized in the device configuration interface. After the configurations are completed, the system will save configurations automatically.
- Page 18 Output Settings. To connect one power amplifier to the partition extender, select single channel; to connect two power amplifiers to the partition extender, select double channel. A single channel supports only one broadcast output. You can select any channel 1, 2, 3, or 4 as the output channel.
- Page 19 (6) Broadcast List Setting ： Set the broadcast audio file playlist (need to add audio files in the "Media Library" in advance). After the configurations are completed, the system will save configurations automatically. (7) Set audio source priority： Set the audio source type (BGM/Business/Emergency) and priority of...
- Page 20 the device input channel and playlist. After the configurations are completed, the system will save configurations automatically. (8) Set Group: On Grouping Setting, multi-zone can be conbined to one group. (9) Control output ： Enter the name of the Control output, check the control output to be...
- Page 21 added.After the configurations are completed, the system will save configurations automatically. (10) Set the broadcast pattern：Set the broadcast pattern, which is used to set the mode selection when schedule broadcast and control broadcast.After the configurations are completed, the system will save configurations automatically. 4.1.3 Set the timer to start broadcasting On the "Schedule Broadcast Settings"...
- Page 22 4.1.4 Set control to start broadcasting On the "Event Broadcast Settings" interface, set the task name, broadcast pattern, and control input. When the control input of the device is triggered, the specified broadcast mode will be activated.
- Page 23 4.1.5 Set button to start broadcast On the "Matrix Settings" interface, you can set the broadcast pattern corresponding to the [Preset 1]-[Preset 3] keys of the matrix controller. Press the device's [Preset 1]-[Preset 3] key to start the specified broadcast pattern.
- Page 24 4.1.6 Set remote microphone function On the "Remote Settings" interface, you can configure the remote microphone.
- Page 25 Set the number of extention units connected to the Extention remote microphone, and support up to 9 extention unit setting units. PTT mode: When broadcasting, press the selection key first, and then continue to hold the broadcast speech key, then you can initiate a call. Release the talk button PTT/LOCK to end the broadcast.
- Page 26 Select the control output mode. The corresponding list shows the control output list set on the VX-1000 control Control output mode interface. After setting the control output output mode, press corresponding button, pattern corresponding control output is closed, and press the button again, the corresponding control output is disconnected.
- Page 27 4.2 Initiate broadcast 4.2.1 Audio broadcasting (1) Rotate the [OPERATE Button] to select the target input (4 audio inputs, only single selection), press the [OPERATE Button] to confirm the selection； (2) Rotate the [OPERATE Button] or press the corresponding partition key to select the target output (support multiple selection), press the [OPERATE Button] to confirm the selection；...
- Page 28 (3) Press the [START Button] to start broadcasting. (4) Additional broadcasting (maximum support for simultaneous 4-channel broadcasting)： Rotate the [OPERATE Button] on the interface during the broadcast, select "Add broadcast", and press the [OPERATE Button] to confirm the selection. Select the target input and output (the operation method is the same as above), press [START Button] to initiate the second broadcast.
- Page 29 (2) Press the [START Button] to start broadcasting. At this time, press the button on the left side of the microphone to start voice shouting. (3) Release the button on the left side of the handheld microphone, and the broadcast sound output stops.
- Page 30 state. (2) Rotate the [OPERATE Button] to select the target input (4 audio inputs, only single selection), press the [OPERATE Button] to confirm the selection. (3) Rotate the [OPERATE Button] or press the corresponding partition key to select the target output (support multiple selection), press the [OPERATE Button] to confirm the selection.
- Page 31 broadcast is stopped. 4.3 Monitoring (1) Press the [AUDIO MONITOR Button], the monitor status light is steady green, and the device enters the monitor state. (2) Rotate the [OPERATE Button] to select the monitor input audio source or zone output audio (Note: only one target can be monitored at the same time).
-
Page 32: System Menu
4.4 System menu 4.4.1 Volume Adjustment (1) Press the [MENU Button] to enter the system menu interface, rotate the [OPERATE Button], select the "Volume adjustment" module, press the [OPERATE Button] to confirm the selection. Rotate the [OPERATE Button] to select the volume of the target area, and press the [OPERATE Button] to confirm the selection. - Page 33 4.4.3 Device Information Press the [MENU Button] to enter the system menu interface, rotate the [OPERATE Button], select the "Device Information" module, and press the [OPERATE Button] to confirm the selection. View device IP address, firmware version, MAC address and other information.
-
Page 34: Troubleshooting
5. TROUBLESHOOTING 5.1 Troubleshooting 5.1.1 Manually initiate a sound source broadcast without sound? 1）Check whether the device audio source input interface or auxiliary audio source input interface has audio input. Press the monitor button to monitor the audio source input channel, whether there is sound output from the left speaker on the front panel;... - Page 35 Step two：Use a Phillips screwdriver (or electric screwdriver) to remove the four M3*4 countersunk cross screws on the right side bracket of the device and remove the right side bracket. Step three：Locate the button battery at the J8 position on the lower motherboard, and use tweezers to remove the battery and replace it.
- Page 36 Battery Step four：Reinstall the removed bracket and cover.
-
Page 37: Specification
6. APPENDIX 6.1 Specification 6.1.1 VX-1000MC-W Matrix Controller Model VX-1000MC-W AC POWER IN A/B：AC220-240V，50Hz/60Hz，European Power Supply standard terminal Power Consumption 16.65W 4 Channels，European standard terminal，Balanced，Input Audio Input impedance 10KΩ，Rated input 0dB 4 Channels， RCA Terminal， Unbalanced， Input impedance 10K Auxiliary audio input Ω，Rated input 0dB；Mixing with audio input interface... - Page 38 6.1.2 VX-1000PF-W Peering Frame Model VX-1000PF-W AC POWER IN A/ B：AC220V-240V，50Hz/60Hz，European standard Power Supply terminal 3.5W（When the main power port & power amplifier unit is not Power Consumption inserted） Power Amplifier Module 4 channels slot Stand-by Amplifier 1 channels Module slot Operation temperature -10℃~+55℃...
- Page 39 TOA Corporation 202108...