Table of Contents
Advertisement
Notes
• The VOR system depends on the environment conditions. If you cannot get the
desired results, set VOR to OFF.
• When using the VOR system, the unit starts recording only when a sound is
detected, therefore, the beginning of the word may not be recorded. For an
important recording, we recommend setting VOR to OFF.
To monitor the sound
Connect an earphone (supplied) firmly to the EAR jack. The sound for
monitoring cannot be adjusted by VOL.
Start recording during playback
Press r (record) during playback, recording starts immediately. It is useful
when you want to re-record the portion which was just recorded.
Review the portion just recorded
Push up CUE/0•)/REVIEW toward )REVIEW during recording.
Release the button at the point to start playback.
Recording cue markers
While recording, you can record a special signal on the tape to mark a
specific position.
At the desired position, press CUE MARKER to record a signal. The REC
lamp goes off and a signal will be recorded on the tape. If you want to
record a signal longer than that, press CUE MARKER as long as you want.
During cue and review, you will hear the beep sound at the signal position.
During playback, you will hear the signal with low frequency sound at the
signal position.
Notes
• We recommend recording cue markers when there is a break in the sound.
• During cue and review, the beep sounds differently.
• The beep may sound differently depending on the marked position on the tape
because the winding speed varies from the beginning to the end of the tape.
At the end of the tape
In the recording or playback mode, the tape stops at the end of the tape and
the locked buttons will be released automatically (Automatic shut-off
mechanism).
After fast forward or rewind, be sure to set CUE/0•)/REVIEW back
to the center.
Recording/Playback with the Connected
Equipment
Notes
• When connecting cords, be sure you connect plugs firmly.
• The example uses Sony products. If you have any problem when using other
products, read the instruction manual of those products.
Recording from another tape recorder G-a
Set this unit to the recording mode and another tape recorder to the
playback mode. In this case set VOR to OFF.
Dubbing onto another tape recorder G-b
Set this unit to the playback mode and another tape recorder to the
recording mode.
Recording with an external microphone G-c
Connect a microphone to MIC. When using a plug-in-power system
microphone, the power to the microphone is supplied from this unit.
z Additional Information
Precautions
On power
Operate the unit only on 3V DC. For AC operation, use the AC power
adaptor recommended for the unit. Do not use any other type. For battery
operation, use two size AA (R6) batteries.
On the unit
• Use only the y (standard microcassetes) with this unit. Non-
standard cassette cannot be used because the "L" dimension (see Fig. A)
is different.
To prevent a tape from being accidentally recorded over (see
Fig. F)
Break out and remove the cassette tabs. To reuse the tape for recording,
cover the tab hole with adhesive tape.
•Do not leave the unit in a location near heat sources, or in a place subject
to direct sunlight, excessive dust or mechanical shock.
•Should any solid object or liquid fall into the unit, remove the batteries or
disconnect the AC power adaptor, and have the unit checked by qualified
personnel before operating it any further.
•When you do not use the unit for long, remove the batteries to avoid
damage caused by battery leakage and subsequent corrosion.
•If the unit has not been used for a long time, set it in the playback mode
and warm it up for a few minutes before inserting a tape.
Keep personal credit cards using magnetic coding or spring-wound
watches etc. away from the unit to prevent possible damage from the
magnet used for the speaker.
If you have any questions or problems concerning your unit, please consult
your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks, consult your
nearest Sony dealer.
You cannot insert the cassette.
m
The cassette is inserted front side back.
m
9 (play) is pressed.
You cannot close the cassette compartment lid.
m
The cassette is inserted into the wrong part (it should be inserted into the lid
side).
m
9 (play) is pressed.
Playback is not possible even if you press 9 (play).
m
The tape has reached the end. Rewind the tape.
m
The batteries are weak. Replace both batteries with new ones.
You cannot press r (record).
m
There is no cassette.
The tab on the tape has been removed. To reuse the tape for recording, cover
m
the tab hole with adhesive tape.
You cannot press r (record) and 9 (play).
m
The tape has reached the end. Rewind the tape.
m
After the atuomatic shut-off, C PAUSE is slid in the direction of the arrow.
Recording cannot be made.
m
The batteries are weak. Replace both batteries with new ones.
m
The head is contaminated.
m
VOR has been set to the improper position when VOR function works.
Recording is interrupted.
m
VOR is set to L or H. When you do not use VOR, set it to OFF.
Recording cannot be erased completely.
m
The head is contaminated.
During CUE0/)REVIEW the tape stops or does not run.
You cannot fast-forward or rewind.
m
The batteries are weak. Replace both batteries with new ones.
The unit does not operate.
m
The batteries have been inserted with incorrect polarity.
m
The batteries are weak. Replace both batteries with new ones.
m
C PAUSE is slid in the direction of the arrow.
m
The AC power adaptor or car battery cord is not firmly connected.
m
The batteries have been inserted, but simultaneously the AC power adaptor is
connected and not to be done to the wall outlet.
No sound comes from the speaker.
m
The earphone is plugged in.
The volume is turned down completely.
m
The sound drops out, sound quality becomes worse or sound
has excessive noise.
m
The volume is turned down completely.
m
The batteries are weak. Replace both batteries with new ones.
m
The head is contaminated.
Tape speed is too fast or too slow in the playback mode.
Improper setting of the TAPE SPEED switch. Set it to the same speed as that
m
used for recording.
Tape speed is faster than the normal playback speed.
m
The FAST PB switch is slid in the direction of the arrow.
Maintenance I
To clean the tape head and path
Press 9 (play) and wipe the head 1, capstan 2 and the pinch roller 3
with a cotton swab, moistened with alcohol every 10 hours of use.
To clean the exterior
Use a soft cloth slightly moistened in water. Do not use alcohol, benzine or
thinner.
Advertisement
Table of Contents
