Page 2
ZOTAC. Products and corporate names mentioned in this manual may not be registered trademarks or copyrights of their respective companies, and are respective owners.
Installing a hard disk -------------------------------------------------------------------------- 13 Connecting a S/PDIF cable ------------------------------------------------------------------ 15 ---------------------------------------------------------- 16 --------------------------------------------------------- 18 Mounting the ZOTAC ZBOX nano to a LCD monitor ---------------------------------- 18 --------------------------------------------------------------- 20 Installing an operating system -------------------------------------------------------------- 20 Installing system drivers ---------------------------------------------------------------------- 20...
ZOTAC ZBOX nano Safety information Your ZOTAC ZBOX nano is designed and tested to meet the latest standards of safety for read the following safety instructions. Setting up your system Read and follow all instructions in the documentation before you operate your system.
Welcome Congratulations on your purchase of the ZOTAC ZBOX nano mini-PC. The following illustration displays the package contents of your new ZOTAC ZBOX nano. Please contact your retailer If any of the below items are damaged or missed. 1 x ZOTAC ZBOX nano mini-PC...
ZOTAC ZBOX nano Getting to know your ZOTAC ZBOX nano Front view Refer to the diagram below to identify the components on this side of the system The power switch turns the mini-PC ON and OFF. The hard disk LED blinks when data is being written onto or read from the hard disk drive The IR receiver is used to receive signals from the IR remote control.
ZOTAC ZBOX nano Rear view Refer to the diagram below to identify the components on this side of the system. The supplied power adapter converts AC power to DC power for use with this jack. Power supplied through this jack supplies power to the mini-PC. To prevent damage to the mini-PC, always use the supplied power adapter.
BIOS settings such as integrated IR receiver, and USB 2.0 charge, . How to disable integrated IR receiver Turn on the ZBOX nano mini-PC, then press <Delete> to enter the BIOS SETUP UTILITY. Use the arrow keys to navigate to...
Page 10
ZOTAC ZBOX nano Enter and select : enable the internal IR receiver (default) : disable the internal IR receiver...
ZOTAC ZBOX nano How to enable USB 2.0 charge (for S3/S4/Sleep status) menu, select Enter and select Note: Before charging via USB 2.0 in S5 status, please make sure the Deep S5 (Deep Sleep in menu) is disabled.
Page 12
ZOTAC ZBOX nano Customizing the ZOTAC ZBOX nano Before installing hardware, please follow the instructions below to remove the cover of your ZOTAC ZBOX nano. 1. Remove the four screws securing the bottom cover into place.
ZOTAC ZBOX nano Installing a memory module 1. Locate the SO-DIMM memory slot and insert a SO-DIMM memory module into the slot at a 45 degree angle. of the memory slot.
ZOTAC ZBOX nano Installing a hard disk 1. Locate the hard disk bracket, remove the 2 screws, and remove the hard disk bracket as shown in the image below. 2. Install the hard disk bracket onto a 2.5-inch SATA hard disk with 2 screws.
Page 15
ZOTAC ZBOX nano 4. Reinstall the screws for the hard disk bracket.
ZOTAC ZBOX nano Connecting a S/PDIF cable 1. Connect the S/PDIF cable to the mini-Optical S/PDIF adapter. 2. Locate the front panel and connect the mini-Optical S/PDIF adapter to the headphone / mini-Optical S/PDIF jack.
Page 17
ZOTAC ZBOX nano Setting up the ZOTAC ZBOX nano Please connect your peripherals before using your ZOTAC ZBOX nano. Connect the DisplayPort connector to the DP port. the USB 3.0 port.
Page 18
ZOTAC ZBOX nano Connect the supplied AC adapter to the DC IN jack on the system rear panel and then press the power switch on the front panel to turn on the system. Connect one end of an HDMI cable to the HDMI port on the system rear panel by default.)
4 inches (10 cm) of spacing in front of the ventilation holes. interference. Mounting the ZOTAC ZBOX nano to a LCD monitor monitor. Disclaimer: ZOTAC cannot be held liable for damages resulting from an improper installation. to secure the ZBOX to the mount.
Page 20
ZOTAC ZBOX nano Connect the ZOTAC ZBOX nano to your LCD monitor with an HDMI/DP cable.
Installing system drivers Before you can use the full features of the ZOTAC ZBOX nano, the system drivers must be installed. The following types of operating systems are supported by the Follow the instructions below to install the system drivers: installation main menu will show up automatically.
Select the driver you want to install. The driver installer should launch. Follow the onscreen instructions for the selected driver to install. Restart the system. Using your ZOTAC ZBOX nano Please follow the instructions below to connect to a wireless network: area.
ZOTAC ZBOX nano Repeat Step 1-3 in the previous section. Select “Obtain an IP address automatically” and click “OK”. Click “Next”. Select “Connect to the Internet” and click “Next”. Select “Set up my connection manually”. Select your connection type and click “Next”.