Related Manuals for Jet JPT-F260-M
Summary of Contents for Jet JPT-F260-M
- Page 1 JPT-F260-M PLANER & THICKNESSER JPT-F260-T Original: Operating Instructions Translations: Mode d´emploi TOOL FRANCE S.A.S 9 Rue des Pyrénées 91090 LISSES France www.promac.fr M-JPT-F260-M & JPT-260-T 2022-03...
- Page 2 CE‐Konformitätserklärung Déclaration de Conformité CE Product / Produkt / Produit: Planer & Thicknesser / Abrichthobelmaschine / dégauchisseuse JPT-F260-M / JPT-F260-T Brand / Marke / Marque: Manufacturer or authorized representative/ Hersteller oder Bevollmächtigter/ Fabricant ou son mandataire TOOL FRANCE S.A.S 9 Rue des Pyrénées，91090 LISSES, France We hereby declare that this product complies with the regulations Wir erklären hiermit, dass dieses Produkt der folgenden Richtlinie entspricht...
-
Page 3: Declaration Of Conformity
UK Declaration of Conformity Product: Planer & Thicknesser Model: JPT-F260-M / JPT-F260-T Brand: Manufacturer or authorized representative: TOOL France S.A.S Unit 1a Stepnell Park Off Lawford Road Rugby CV21 2UX United Kingdom We hereby declare that this product complies with the regulation:... -
Page 4: Table Of Contents
Dear Customer, Many thanks for the confidence you have shown in us with the purchase of your new JET-machine. This manual has been prepared for the owner and operators of a JET JPT-F260-M / JPT-F260-T Planer Thicknesser to promote safety during installation, operation and maintenance procedures. -
Page 5: Remaining Hazards
Always wear the approved working Connection and repair work on the outfit: electrical installation may be carried out - safety goggles by a qualified electrician only. - ear protection - dust protection Maintain a balanced stance at all times. Do not operate the machine when you are tired. -
Page 6: Machine Specifications
4. Machine specifications Operating position 1: Fig 1 Idling LpA 74,4 dB(A) 4.1 Technical data Operating LpA 91,8 dB(A) A….Outfeed table JPT-F260-M & JPT-F260-T: B….Jointer fence Operating position 2: C….ON/OFF switch Planing Idling LpA 84,4 dB(A) D….Cutterblock guard Jointing width... -
Page 7: Assembly
ATTENTION: mounting bracket (G) sufficiently for the Replace the handle and secure in place The planer tables are precisely aligned next step. Lightly tighten clamping with the Phillips screw/spring, see Fig 7. ex. works. They may only be loaded Repeat for the opposite. handle, see Fig 4. -
Page 8: Dust Connection
Mains connection and any extension The power feed can be engaged and Planing the face of a work piece up cords used must comply with applicable disengaged with handle (L, Fig 2). to 75mm thick: regulations. Place the work piece against the jointer In case of machine overload the motor fence. -
Page 9: Thicknessing
Work pieces shorter than 150mm may front, hollow side downward. body by 1,1mm in radius. not be processed. Plane the stock with the grain, if Use genuine Jet replacement parts Machine max. 2 work pieces at one possible. only. time. Feed on both outer sides. -
Page 10: Setting The Machine For Thicknessing
Fig 18 Fig 21 Remove the blade holder and lay aside. Clean the slot housing thoroughly, Holding the blade and setting tool (L) in remove any resin build-up, sawdust, chips etc. Clean the blade holder and position, tighten two cap head screws to ensure the circumference of the cutter provide a firm clamp on the blade. -
Page 11: Digital Thickness Display
If breaking time should exceed 10 accurate visual indication of the amount seconds, the motor break assembly you are adjusting the thicknessing table needs to be replaced. Contact your Jet in 0.10mm increments. service station immediately. The digital display should be pre-set at the fatory but if required can be set as follows. -
Page 12: Environmental Protection
*Moisture content too high *Resin build-up on tables- clean and wax table surfaces. Snipe *Inadequate support of long boards- *Dull knives- use helping roller stand. install sharp knives. *Dull knives- sharpen knives. 10. Environmental protection *Knives set too high- Protect the environment. adjust the knives set the outfeed table higher.