Related Manuals for Nostalgia Electrics Vintage CCP-200
Summary of Contents for Nostalgia Electrics Vintage CCP-200
- Page 1 All products are trademarks of Nostalgia Products Group, LLC. Worldwide design & utility patented or patents pending. © 2009 Nostalgia Products Group, LLC. www.nostalgia electrics.com (rev. 08/21/09)
- Page 2 Old-Fashioned Movie-Time Popcorn Cart™ Instructions and Recipes (French) Old-Fashioned Movie-Time Popcorn Cart™ Instructions et Recettes (Spanish) Old-Fashioned Movie-Time Popcorn Cart™ Instrucciones y Recetas...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT PRECAUTIONS IMPORTANT SAFEGUARDS ....2 INTRODUCTION ......3 PARTS &... -
Page 4: Important Precautions
IMPORTANT PRECAUTIONS NEVER immerse in water. NEVER use near water. NEVER use an abrasive sponge nor cloth. NEVER use a scouring pad on the appliance. NEVER leave appliance unattended while in use. NEVER force Kettle in nor out of the brackets as this may cause gears to become misaligned and appliance will not operate properly. -
Page 5: Introduction
INTRODUCTION Thank you for purchasing the OLD FASHIONED MOVIE TIME POPCORN CART™, a product in Nostalgia Electrics’ Vintage Series™. This 48” tall vendor-style popcorn cart will be the hit of every party. It pops up to two quarts of hot, fresh, kettle cooked popcorn per batch. Providing a vintage look and feel, reminiscent of silent movie houses and carnivals circa-early 1900’s, the OLD FASHIONED MOVIE TIME POPCORN CART™... -
Page 6: Parts & Assembly
PARTS & ASSEMBLY Hardware #1 Screw (10mm) #2 Bolt (10mm) Qty. 4 Qty. 6 #5 Flat Washer #6 Nut Cap Qty. 8 Qty. 6 #3 Bolt (20mm) #4 Stud (65mm) Qty. 4 Qty. 4... - Page 7 Assembly (A) Main Unit (B) Kernel Measuring (C) Storage (D) Oil Measuring Compartment Spoon (E) Push Handle (F) Axle Rod (G) Wheel (H) Wrench (I) Base Support (J) Bottom Plate (K) Cross Bar (L) Leg Assembly (M) Popcorn Scoop...
- Page 8 Assembly of Base Support Push Handle (E) attaches onto the Storage Compartment (C) using supplied #1 Screws. Insert Cross Bar (K) into the square inserts on the inside of Base Support (I) and secure from below with #2 Bolts. Insert the Leg Assembly (L) over the protruding ends of the Base Support (I) and fasten #4 Studs and #6 Nut Cap.
- Page 9 Assembly of Wheels Insert Axle Rod (F) into Base Support (I). Put on #5 Flat Washer. Slide Wheel (G) into Axle Rod (F) and add a second #5 Flat Washer. Use Wrench (H) to tighten the #6 Nut Cup. Add #5 Flat Washer, second Wheel (G), another #5 Flat Washer, and #6 Nut Cap to the other side of the Axle Rod (F), following the directions above.
-
Page 10: How To Operate
HOW TO OPERATE Before first use, clean the inside of the unit by wiping with a moist, non-abrasive sponge, towel or cloth and then wipe with a non- abrasive dry towel. Wipe down the inside of the Kettle and be sure it is properly placed in the brackets before starting. -
Page 11: Helpful Tips
HELPFUL TIPS SMOKING If your OLD FASHIONED MOVIE TIME POPCORN CART™ begins to smoke during cooking, it may be due to grease build up. In order to reduce smoking, make sure that you clean the inside of the Kettle between uses. CLEANING &... -
Page 12: Returns & Warranty
RETURNS & WARRANTY SHOULD YOUR UNIT NOT WORK OR IS DAMAGED WHEN YOU FIRST TAKE IT OUT OF THE BOX, PLEASE RETURN IT TO THE PLACE OF PURCHASE IMMEDIATELY. OLD FASHIONED MOVIE TIME POPCORN CART™ / CCP-200 Should you have any questions, please contact us via email or at the customer service number listed below between the hours of 8:00 AM and 5:00 PM, Monday through Friday, Central Standard Time.