Marantz SR7200 User Manual page 29

3. Erasing Jog Dial Codes
To clear all codes and names previously set for each of the
functions (DVD, TV, etc.).
1) Press the function you want to erase.
2) Hold down the CLEAR button ⁄5 and press both ENT buttons
m at the same time. LCD b will display CLR?.
ENT ENT
CH
C D
DSS T V
L D TUNER
CLEAR CLEAR MEMO
AUTO
1 2
DSP 6-STEREO
3) If you wish to continue the clearing operation, press the OK
Cursor button ⁄0 . This will return all 10 commands in the Jog
Dial to their factory presets, or leave them empty if no factory-
presets are available. Accordingly, the LCD b will return to
the factory preset displays, or will simply be empty.
CH
C D
• Use a similar operation to erase the Jog Dial codes for each
function.
• To cancel the memory clearing operation, do not press OK
Cursor button ⁄0 and simply touch any other button.
4. Erasing Code s by Function
To clear all codes and names previously set for each of the
functions (DVD, TV, etc.), press and hold the CLEAR button ⁄5 ,
then press the button for the function to be cleared twice. CLR?
will appear on LCD b. If you wish to continue the clearing
operation, press the OK Cursor button ⁄0 .
C D DVD DVD
DSS T V
L D TUNER
CLEAR CLEAR MEMO
AUTO
1 2
This will return the button to its factory-presets or leave it empty if
no factory presets are available. Accordingly, the LCD b will
return to the factory preset displays, or will simply be empty.
• To cancel the memory clearing operation, do not press the OK
Cursor button ⁄0 and simply touch any other button.
• The codes for the < • 3 button ⁄1 cannot be cleared.
ENT ENT
VOL
OK
DVD CD-R/MD
VCR AUX
TAPE AMP
GUIDE MUTE
DTS CS5.1 6.1
3 4 5
2CH 2CH OSD SLEEP
VOL
OK OK
DVD
CD-R/MD
CD-R/MD
VCR AUX
TAPE AMP
GUIDE MUTE
DTS CS5.1 6.1
3 4 5
5. Erasing All Memory Contents
To clear all the memory contents and reset all codes and names to
their factory presets, press and hold the CLEAR button ⁄5 , and
press both the power ON and OFF buttons c simultaneously.
ACLR? will appear on LCD a.
If you wish to continue the clearing operation, press the OK
Cursor button ⁄0 .
This will return the entire memory to its factory-presets, or leave it
empty for items for which no factory presets are available.
Accordingly, the LCD will return to the factory-preset display or will
simply be empty.
• To cancel the memory clearing operation, do not press the OK
Cursor button ⁄0 and simply touch any other button.
After the OK Cursor button ⁄0 is pressed, clearing the entire
memory will take approximately 5 seconds.
PROGRAMMING MACROS
Macros make it possible to use a single function button to perform
more complex series of operations that would normally require
pressing several buttons. A single button can be programmed to
perform up to 10 steps in sequence. A typical example of such a series
might be as follows:
• Turn the main amplifier power ON → Switch the function to DVD →
Set the Surround Mode to Pro Logic → Switch the TV to video input
→ Set the DVD player to PLAY.
• No signals may be transmitted during macro programming.
• The various steps that make up a macro are set initially to be sent
one after another in 1 second intervals, however these intervals
may be shortened to as little as 0.5 seconds or lengthened to as
much as 5 seconds using the Setup mode.
• In the macro mode, the number of steps the macro contains is
displayed on LCD c. Macros may be programmed for each of the
11 function buttons, from DVD to AMP.
1. Use a ballpoint pen or other sharp point to press the MACRO
button x until the MACRO and LEARN indicators are displayed
blinking on the LCD.
POWER
SOURCE
ON
ON / OFF
LEARNING REMOTE
7200SR
CONTROL RC
Press the Function button , for which you wish to program a
2.
series of operations. In this case, let's use the example of the DVD
player.
Press the DVD Function button ,. The LCD a will display DVD-
M.
Characters displayed on LCD a include the following, depending
on the function button for which the macro is being programmed:
LD-M, DVD-M, TV-M, DSS-M, VCR-M, AUX-M, TUN-M, CD-M,
TP-M, AMP-M, CDR-M (or MD-M for remote controller set for
MD).
• If a macro has already been set for the selected function button,
the LCD a will blink. Also, the number of steps in the macro is
displayed on LCD c.
22
OFF
MACRO MODE