Mackie SA1532Z User Manual
  1. Manuals
  2. Brands
  3. Mackie Manuals
  4. Speaker System
  5. SA1532Z
  6. User manual

Mackie SA1532Z User Manual

3-way active loudspeaker system
Hide thumbs Also See for SA1532Z:
Table of Contents

Advertisement

Quick Links

See also: Repair Manual
SA1532
z
3-WAy Active
LOUDSpeAker SySteM
USer'S MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Mackie SA1532Z

Summary of Contents for Mackie SA1532Z

  • Page 1 SA1532 3-WAy Active LOUDSpeAker SySteM USer’S MANUAL...

  • Page 2: Important Safety Instructions

    1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

  • Page 3: Table Of Contents

    1.75-inch neodymium compression driver. The low frequencies are produced by two high-output 15-inch woofers. Connecting and setting up the SA1532z is a breeze. It accepts a line-level signal via a female XLR input jack. CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...2 INTRODUCTION ...3...

  • Page 4: Rear Panel Description

    See “Thermal Considerations” on page 6. 8. POWER Switch Use this switch to turn the SA1532z on and off. Make sure the level control is turned down before you turn it 9. AC Receptacle This is where you connect the AC linecord to provide AC power to the SA1532z’s built-in power amplifiers.

  • Page 5: Hookup Diagram

    — so the signal coming out of the LOOP OUT jack is exactly the same as the signal going in. pLAceMeNt The SA1532z speaker is designed to sit on the floor or stage. You can create a horizontal array by placing the cabi- nets side-by-side.

  • Page 6: Room Acoustics

    If the thermal switch activates frequently, try turning down the level control a notch or two on the mixing con- sole (or the back of the SA1532z) to avoid overheating the amplifier. If the temperature in the room is too high, it could cause the amplifier to overheat.

  • Page 7: Service Information

    AC cables, power transformers, or other EMI-induc- ing devices. • Is there a light dimmer or other SCR-based device on the same AC circuit as the SA1532z? Use an AC line filter or plug the SA1532z into a different AC circuit. •...

  • Page 8: Repair

    Non-warranty repair for Mackie products is available at a factory-authorized service center. To locate your near- est service center, visit www.mackie.com, click “Support” and select “Locate a Service Center.” Service for Mackie products living outside the United States can be obtained through local dealers or distributors.

  • Page 9: Sa1532Z Specifications

    “Mackie” and the “Running Man” figure are registered trademarks of LOUD Technologies Inc. All other brand names mentioned are trademarks or registered trademarks of their respective holders, and are hereby acknowledged.
  • Page 10 LIMIT DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA THERMAL COPYRIGHT ©2004 • THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.: "MACKIE", AND THE "RUNNING MAN" FIGURE • PATENT PENDING 13.9 in/ 35.3 cm CAUTION WARNING: STANDARD USE. TO ENSURE PROPER OPERATION ALLOW A MINIMUM OF 6 INS.

  • Page 11: Sa1532Z Limited Warranty

    To obtain repairs or replacement under warranty, you must have a copy of your sales receipt from the authorized Mackie dealer where you purchased the product. It is necessary to establish purchase date and determine whether your Mackie product is within the warranty period.
  • Page 12 16220 Wood-Red Road NE • Woodinville, WA 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Central and South America: 425.487.4333 Middle East and Africa: 31.20.654.4000 Fax: 425.487.4337 • www.mackie.com E-mail: sales@mackie.com...

Table of Contents