A Ppearance C Hoices; Eatures Nd Pecifications; Features And Specifications - Lennox Hearth Products Winslow PS40 Installation And Operation Manual

features and Specifications

i o
nstaLLation ptions
• Residential
• Vented vertical and horizontal (see venting instruc-
tions)
• Manufactured home and mobile home
• Thermostat or manual operation
• Bedrooms
h
eating
• Max. feed rate is 4.7 pounds/hour or 39,500 BTU/hour
• Min. feed rate is 1.8 pounds/hour or 15,120 BTU/hour
v
enting
This stove is approved for venting with Type L and Type
PL pellet vent pipe. The flue collar on the stove accepts
3"diameter pipe.
The combustion air for this stove is drawn through a pipe
at the lower rear of the stove. For mobile home installations
a 3" ID flex line or pipe must be attached to the stove's air
intake to draw air from outside the house. The vent pipe can
be installed vertically or horizontally (see Venting section
for recommended installations).
e
LectricaL
• The stove requires 120 volts AC for operation.
• Maximum wattage is 700.
• Igniter wattage is 400.
• Normal operating wattage is 300.
t
hermostat
This stove can be operated manually or with a thermostat.
L
ighting
This stove is equipped with an electric self igniter for ease
of ignition.
F s
ueL peciFications
This stove is designed to burn wood pellet fuel. In addition,
a corn/wood pellet mixture, with a maximum of 50 percent
corn can be burned. Burning any other fuel that is not ap-
proved for use with this appliance will void the appliance
warranty. IMPoRTANT: The corn/wood mix needs to be
mixed evenly before being put in the Winslow™ pellet
stove hopper.
Wood Pellet Specifications: This appliance has been
designed to burn wood residue pellets with up to 3% ash
content. Dirty fuel will adversely affect the performance of the
stove. Any questions regarding pellet fuel can be answered
at the Pellet Fuels Institute (PFI), www.pelletheat.org.
CAUTIoN: THe USe of UNAPPRoVeD, DIRTY, WeT
AND/oR HIGH SALT CoNTeNT fUeL WILL VoID THe
WARRANTY!
Wood pellets manufactured to the pellet fuels institute (P.F.I.)
certification standard are available in two grades, Standard
and Premium. The primary difference between the two is
the ash content of the pellets.
The P.F.I. specification for standard grade & premium grade
residential pellet fuel is as follows:
• CHLORIDES (Salt): Less than 300 p.p.m. to avoid stove
and vent rusting.
• BULK DENSITY: 40 lb. / Cu. Ft. minimum
• MOISTURE CONTENT: 8% maximum
• ASH CONTENT: < 3% maximum (standard grade) < 1%
maximum (premium grade)
• FINES: 0.5% maximum through a 1/8" screen
• BTU CONTENT: There are a number of variations in pellet
fuels that are not included in PFI standards. For example,
BTU (heat value) content may range from just under 8,000
to almost 9,000 Btu, depending upon species and region
of the country and other variables.
Corn Specifications: Use only clean-shelled corn with a
moisture content less than 15% and approximate fuel value
of 7000 BTU/lb (16,200 kJ/kg). Do not attempt to burn corn
with higher moisture content or burn lesser grade fuels. Do
not burn other types of agricultural pellets or byproducts
(alfalfa, cherry pits, olive pits, nut shells, etc.) as they are
not permitted to be burned in these appliances.
w
eight
h
opper
L
isting inFormation
The Winslow™ PS40 stove is safety tested and listed with
the following agencies;
• OMNI-Test Laboratories, Inc., Beaverton, Oregon to ASTME
1509
• USEPA List of Exempt Wood Heating Appliances
• List of Colorado Approved Pellet Stoves
a
ppearance
The Winslow PS40 stove can be ordered with the following
door trims and grills, log set, and brick panel options:
Door Trim Kits
Black
Gold
Nickel
Brushed Nickel
Black Nickel
Log Set - Required
brick Panel Kit -Required
NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe.
- 265
pounds
c - 60
apacity pounds
c
hoices
79038
79034
79037
79035
79036
H5142
79030
Grill Kits
Black 79000
Gold 79001
Nickel 79002
Brushed Nickel 79022
Black Nickel 79039