Advertisement
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
Thank you for purchasing this Holmes
®
product. We
7. Always unplug the heater when not in use.
understand the value of quality and are committed to
8. When unplugging, be sure to pull by the plug and not
making superior products that stand the test of time. We
the cord.
trust this product will exceed your expectations of quality
9. DO NOT insert or allow foreign objects to enter any
and reliability. We hope that you enjoy this product and
ventilation or exhaust opening as this may cause an
will consider purchasing another Holmes
®
product in the
electric shock or fire, or damage the heater.
future. To see our full product line or if you have any
10. DO NOT operate heater with a damaged cord or plug,
questions or comments about this product, please visit our
or after the heater malfunctions, has been dropped or
website at: www.holmesproducts.com.
damaged in any manner. Return appliance to
manufacturer for examination, electrical or mechanical
When using electrical appliances, basic safety precautions
adjustment, or repair.
should always be followed to reduce the risk of fire, electric
11. A heater has hot and arcing or sparking parts inside.
shock, and injury to persons, including the following:
DO NOT use it in areas where gasoline, paint, or
1. Read all instructions before using the appliance.
flammable liquids are used or stored.
2. To avoid fire or shock hazard, plug the appliance
12. Use appliance only for intended household use as
directly into a 120V AC electrical outlet.
described in this manual. Any other use not
3. The heater is hot when in use. To avoid burns, DO NOT
recommended by the manufacturer may cause fire,
let bare skin touch hot surfaces. If provided, use
electric shock, or injury to persons. The use of
handles when moving this heater. Keep combustible
attachments not recommended or sold by The
materials, such as furniture, pillows, bedding, papers,
manufacturer may cause hazards.
clothes, and curtains at least 3 ft (0.9 m) from the
13. DO NOT use outdoors.
front of the heater and keep them away from the
14. To prevent a possible fire, DO NOT block air intakes or
sides and rear.
exhaust in any manner. DO NOT use on soft surfaces,
4. DO NOT run cord under carpeting. DO NOT cover cord
like a bed, where openings may become blocked.
with throw rugs, runners, or the like. Arrange cord away
15. To disconnect heater, turn controls to OFF, then remove
from traffic area and where it will not be tripped over.
plug from outlet.
5. This heater is not intended for use in bathrooms,
16. Avoid the use of an extension cord because the
laundry areas and similar indoor location. NEVER
extension cord may overheat and cause a risk of fire.
locate heater where it may fall into a bathtub or other
However, if you have to use an extension cord, the
water container.
cord shall be No. 14 AWG minimum size and rated not
6. Extreme caution is necessary when any heater is used
less than 1875 watts.
by, or near children or invalids, and whenever the
17. If the heater will not operate, see specific instructions
heater is left operating and unattended.
on Auto Safety Shut-off.
F E AT U R E S - O P E R AT I O N S
18. DO NOT attempt to repair or adjust any electrical or
shut off. To reset, simply place the heater in an upright
mechanical functions on this unit. Doing so will void
position and press the MODE/OFF button it will operate
your warranty. The inside of the unit contains no user
normally.
serviceable parts. All servicing should be performed by
qualified personnel only.
PRE-OPERATING INSTRUCTIONS
19. Discontinue use if plug or outlet is hot. It is
recommended that the outlet be replaced if plug or
1. Carefully remove your heater from the box. Make
outlet is hot to touch.
certain to remove parts from both sides of the packing
foam. Please save carton for off-season storage.
PLEASE READ AND SAVE
2. Place heater on a firm level surface.
3. Your heater comes fully assembled and ready to use in
THESE IMPORTANT SAFETY
the reduced height configuration.
INSTRUCTIONS
4. To use with pedestal see Assembly Instructions below.
5. Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
TECHNICAL SPECIFICATIONS
NOTE: The power light will illuminate when the heater is
• Wattage: 1500 W (+5% –15%)
plugged in.
• Working voltage: 120v AC/60Hz
OPERATING INSTRUCTIONS
AUTO SAFETY SHUT-OFF
Your heater is equipped with a technologically advanced
This heater is equipped with a patented, technologically-
1Touch
®
electronic thermostat. You can set the heater to
advanced, safety system that requires the user to reset the
run continuously in manual mode or set the 1Touch
heater if there is a potential overheat situation. When a
thermostat to your desired temperature setting. The 1Touch
potential overheat temperature is reached, the system will
thermostat will automatically turn the heater ON or OFF
automatically shut the heater off. It can only resume
depending on the preset comfort level. The comfort level
operation when the user resets the unit.
ranges between 60˚and 80˚ Fahrenheit in a 5˚ increments.
To Reset the Heater:
Manual Mode Instructions:
If the unit shuts down:
1. Plug the heater into a 120V AC electrical outlet.
1. Unplug unit.
2. To start the unit, press the MODE/OFF button once for
2. Wait 10 minutes for unit to cool down.
the HI manual setting. (See Fig. 4)
3. Plug in and operate normally.
3. Press the MODE/OFF button again for the LOW
NOTE: To shut unit OFF, hold Mode/Off button down for 2
manual setting. (See Fig. 4)
seconds.
4. To stop the unit, press and hold the button for two
NOTE: After the heater is shut off the fan will continue to
seconds or keep pressing the button until all the
run for 30 seconds to cool down the inside of the unit.
temperature indicators are OFF.
NOTE: The Power Light will remain lit during operation. In
Tip-Over Shut-Off
Manual Mode, only the LOW or HIGH power light will be lit.
When the unit is accidentally knocked over, it will instantly
NOTE: To shut unit off at anytime press and hold the
F E AT U R E S - O P E R AT I O N S
Mode/Off button for 2 seconds. After the heater is turned
off heater will run for 30 seconds to cool unit.
ASSEMBLY INSTRUCTIONS
If you are planning on using the pedestal, start with Step 1
(Steps 1-6 see Figure 1 to Figure 3)
Step 1 – Turn the heater upside down and place on a firm
level surface.
Step 2 – Unscrew the locking nut by turning
counterclockwise. Slide the locking nut and base
off of the power cord.
Step 3 – Slide the pedestal pole onto the cord – internal
threads first.
Step 4 – Screw the pedestal clockwise onto the (neck)
threaded end on the bottom of the heater until
you feel resistance.
Step 5 – Slide the base and the locking nut onto the cord,
smooth surface facing up. Make sure to align the
dot on the back of the base to the dot on the
neck of the heater.
Step 6 – Hold base straight while tightening the locking
nut by turning clockwise.
®
Step 7 – Insert the power cord through the opening at the
®
rear of the base. Twist to lock in place. (see Figure 3)
Step 8 – Carefully turn the heater upright, place on a firm
level surface.
1TOUCH
®
THERMOSTAT INSTRUCTIONS
OSCILLATION INSTRUCTIONS
To take advantage of the 1Touch
®
thermostat, continue to
1. Select the desired control setting and press or switch
the oscillation button to the ON position.
press the MODE/OFF button until the desired temperature
is set in either the HIGH or LOW setting. When ambient
2. To stop oscillation, press or switch the oscillation button
temperature rises above the set temperature, the heater
to OFF.
will stop. When the ambient temperature drops below the
3. Please do not manually turn the unit; it is designed to
turn only by motorized oscillation.
set temperature, the heater will turn on automatically.
NOTE: When the 1Touch
®
thermostat is set, either
the HIGH or LOW power light, and the set
REMOTE CONTROL INSTRUCTIONS
temperature light will remain lit during operation.
The remote control allows you to control the power, mode,
(See Fig. 4)
and temperature settings of this unit. Please see "Manual
NOTE: It is normal for the heater to cycle ON and
Mode" and "1Touch
®
THERMOSTAT INSTUCTIONS" above.
OFF as it maintains the preset temperature. To
For your convenience a remote control holder is
prevent the unit from cycling, you need to raise the
integrated into the heater.
thermostat setting. When the preset temperature
Insert 2 AAA batteries (not included) into the remote control.
is made, the fan will run for 30 seconds without
heat. This cool down process ensures an accurate
NOTE: To shut this unit off with the remote control you can
and consistent temperature reading.
scroll through all settings until all temperature and power
lights turn off. Remote cannot control oscillation function.
NOTE: 1Touch
®
has memory. The 1Touch
®
thermostat
will remember the previous temperature setting
BATTERY WARNING:
after the unit has been turned off. However, if
• DO NOT mix old and new batteries.
the unit is unplugged, or the unit is turned off, the
• DO NOT mix alkaline, standard (carbon-zinc), or
1Touch
®
thermostat will be reset and will no
rechargeable (nickel-cadmium) batteries.
longer remember the previous setting.
FIGURE 4
A
A. Remote Control
B
Holder
B. IR Lens
D
C
C. Oscillation Button
D. Temp Settings (5)
E. Hi/Lo Power Lights
F. 1Touch
®
Mode/Off
Button
G. Remote Control
Sensor
F
E
E
Advertisement
