Table of Contents
Related Manuals for Neilsen CT0079
Summary of Contents for Neilsen CT0079
- Page 1 1010W IMPACT WRENCH CT0079 ORIGINAL INSTRUCTION SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE. Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. 1010W IMPACT WRENCH Product description: Model: CT0079 Applicable EC Directives: EC Machinery Directive 2006/42/EC EC Directive of Electromagnetic Compatibility 2014/30/EU Harmonized standards... -
Page 3: Specifications
Earthing wire is European directives therefore no necessary Mandatory use of eye protection Wear a mask in dusty Wear noise protection conditions 2. SPECIFICATIONS Model No. CT0079 Rating 230-240V~ 50Hz 1010W Rated Speed 2200/MIN Max torque 450N.m Weight 3.9kg Typical Sound pressure... -
Page 4: Environmental Protection
3. ENVIRONMENTAL PROTECTION o not dispose of this product with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment, at a recognised disposal facility. ACCESSORY This Impact Wrench is delivered supplied with the following components: •... -
Page 5: Personal Safety
PERSONAL SAFETY 1. Stay alert, watch what you are doing and use common sense when you are operating a power tool. Do not operate a power tool when you are tired, ill or under the influence of alcohol, drugs or medication. 2. - Page 6 tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 6. Use recommended accessories. The use of improper accessories could be hazardous. 7. Machine cleanliness. Do not allow the ventilation slots in the machine to become blocked with dust.
-
Page 7: Electrical Connections
7. ELECTRICAL CONNECTIONS This product is provided with a 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing at any time, ensure that a plug of identical specification is used WARNING: THIS APPLIANCE IS OF DOUBLE INSULATED DESIGN No earth conductor is provided. - Page 8 10. OVERVIEW This Impact Wrench is equipped with a 3-position Forward/ Reverse/Neutral trigger switch (item 4 below). When the trigger is squeezed downwards, rotation is forward (clockwise). When squeezed upwards, the direction of rotation is reversed (anti-clockwise), and when in the centre position the tool is stopped.
-
Page 9: Tightening A Nut
11.OPERATING INSTRUCTIONS ALWAYS ENSURE THAT THE MACHINE IS DISCONNECTED FROM THE POWER SUPPLY BEFORE CHANGING THE SOCKET。 WHEN CHANGING FROM FORWARD TO REVERSE OPERATION OR VICEVERSA, ALWAYS ENSURE THE MACHINE HAS FULLY STOPPED BEFORE SWITCHING ON IN THE NEW DIRECTION. LOOSENING A NUT 1. -
Page 10: General Maintenance
4. ALWAYS finish tightening with a torque wrench or suitable spanner. The weight of the vehicle will need to be placed on the wheel to prevent it from rotating while the nuts are tightened. Ensure the final torque applied to the nuts meets the vehicle manufacturer’s recommendations 12.MAINTENANCE CLEANING 1. - Page 11 the same time as a pair. Only use identical brushes from your Clarke dealer. 3. Use a screwdriver to remove the brush holder covers from the machine body. Draw out the worn brushes and insert new ones before replacing the brush holder caps. STORAGE 1.
-
Page 12: Parts Diagram
13.PARTS DIAGRAM... -
Page 13: Parts List
14.PARTS LIST DESCRIPTION DESCRIPTION Plastic Collar Spindle Gear Housing Spur Gear Bearing Sleeve Bearing Thrust Washer Cross-head Screw Spindle Stator Assembly Impact Driver Motor Bearing Ball Bearings Bearing Cap Impact Spring Main Housing Steel Ball Rear Cover Clutch Spindle Cross-head Screw Large Gear Inductor Screw...