Set Up Your Sources - Harman Kardon AVR 2650 Owner's Manual

AVR
6. use the remote's up/down/left/right and ok buttons to select "Speaker Setup."
Speaker Setup
Automatic Setup – EzSet/EQ
Automated Speaker Setup and EQ
Manual Setup
Manually Adjust Speaker Settings
7. Select "Automatic Setup – ezSet/eq" and then select "continue."
8. Select the number of speakers in your system. Select "5.1" if no surround back or
front height speakers are present or if you will be using the Assigned Amp channels
for multizone operation.
9. the test will begin. make sure that the room is quiet while the test noise is playing
through the speakers.
10. when the test finishes, select "continue," then select "view Settings" to see the
results of the ezSet/eq process, or select "done" to exit.
NOTES:
• If there are fewer than five main speakers in your system, do not use the ezSet/eq
process. Instead, proceed as described in manual Speaker Setup , on page 36.
• If you have selected a 6.1-channel configuration with a single surround back speaker,
use ezSet/eq automatic configuration for 5.1 speakers, connect the single surround
back speaker to the left Assigned Amp Speaker output connector, then configure the
surround back speaker manually, as described in manual Speaker Setup, on page 36.

Set Up Your Sources

the Setup Source menu lets you assign the correct physical audio and video connections
to each source and lets you set many audio and video playback features for each source.
IMPORTANT: The "Video Input from Source," "Audio Input from Source" and
"Resolution to Display" settings are not optional and must be adjusted before you
use your AVR to enable playback of each source. you can adjust the other settings
later. See System Settings , on page 39, for complete information about adjusting all of
the Settings menu options.
1. review the input connections you listed on the
buttons table, on page 18. note what changes (if any) you want to make from the
default source-button connector assignments that appear on the list. (If there are no
changes, you can skip this section.)
2. to display the Source Settings menu for the active source, press the Info button on the
front panel or remote. or, from the main menu screen, select "Setup Source" and select
a source from the slide-in menu. the Settings menu for that source will appear.
Cable/Sat
Audio Effects
Video Modes:
Surround Modes:
Audio Format from Source:
Video Input from Source:
Audio Input from Source:
Resolution to Display:
Resolution from Source:
HDMI Bypass:
Change Name:
Adjust Lip Sync
3. Select "video Input from Source" and select the video input connector you want to
assign to the source button. press the ok button. (the setup menu will disappear
from the tv.)
26
Input connections and Assigned Source
Off
Auto Select
NO AUDIO INPUT
HDMI 2
HDMI 2
720p – 60Hz
No Input
Off
Cable/Sat
Cable/Sat
Audio Effects
Video Modes:
Off
Surround Modes:
Auto Select
Audio Format from Source:
NO AUDIO INPUT
HDMI 2
Video Input from Source:
HDMI 2
Audio Input from Source:
720p – 60Hz
Resolution to Display:
Resolution from Source: No Input
HDMI Bypass: Off
Cable/Sat
Change Name:
Adjust Lip Sync
4. press the Info button. the Settings menu for the selected source will reappear.
5. Select "Audio Input from Source" and select the audio input connector you want to
assign to the source button. press the ok button.
Cable/Sat
Audio Effects
Video Modes:
Off
Surround Modes:
Auto Select
Audio Format from Source:
NO AUDIO INPUT
Video Input from Source: Component 1
Analog 1
Audio Input from Source:
Resolution to Display: 720p – 60Hz
No Input
Resolution from Source:
HDMI Bypass: Off
Cable/Sat
Change Name:
Adjust Lip Sync
Resolution to Display: this setting reflects the video output resolution, which is
dependent upon the capabilities of your tv or video display.
• If you connected your tv to the Avr's hdmI monitor out connector, the two devices will
communicate with each other, and the Avr will automatically select the best available
video output resolution. In almost all cases, you should leave the resolution set to the
Avr's automatic selection. (you can override this automatic selection if your video
display's native resolution is different from the Avr's automatic selection.)
• If you connected your tv to the Avr's composite video monitor out connector, you
must set the resolution to "480i" (Avr 3650/Avr 2650) or to "576p" (Avr 365/Avr
265) to view any content.
Audio Effects: this submenu allows you to adjust the dolby volume and dolby plII/
IIx/IIz settings, the bass and treble tone controls, the lfe trim, the equalization on/off
setting and the mp3 enhancement for each source independently. we suggest leaving
this submenu at its default settings and returning to it later if your system requires fine-
tuning. See Audio effects button , on page 34, for more information.
Video Modes: this submenu allows you to make picture adjustments for each source
independently. we suggest leaving the settings at their factory defaults. you should make
picture adjustments to your video display first and use this menu only for fine-tuning. See
video processing , on page 34, for more information.
Surround Modes: this submenu lets you program surround modes for movies, music
and games for each source independently. digital surround signals, such as dolby digital
and dtS bitstreams, are automatically played in their native formats, although you may
change the surround mode. See Audio processing and Surround Sound , on page 33, for
more information.
Audio Format from Source: this line is informational only. when a digital program is
playing, its format will be identified here. when analog audio programs are playing, this
line displays AnAlog.
Set Up the AVR
HDMI 1
HDMI 2
HDMI 3
HDMI 4
HDMI 5
HDMI Front
Component 1
Component 2
Composite 1
Composite 2
HDMI 1
HDMI 2
HDMI 3
HDMI 4
HDMI 5
HDMI Front
Optical 1
Optical 2
Coaxial 1
Coaxial 2
Analog 1