Installation Instructions For The External Supply Plenums; Supply Plenum Clip - Greenheck 452413 Installation, Operation And Maintenance Manual

Installing External Supply Plenums
Fig. 6
OPTION #3
THREADED ROD
SUPPLIED BY OTHERS
1.000 2.125
0.625
OPTION #1
.500 x .375
SLOT (3 PLACES)
HANGING CLIP COULD BE 23.5" FROM
END IF THERE IS A UTILITY CABINET
ON THE END OF THE HOOD
3.000
1.000
1.500
1.000
0.625
HANGING METHODS FOR SUPPLY PLENUMS 4.500
ASP, FSP AND VSP
2.120
1.000
OPTION #1 = HANGING CLIP
147.0°
OPTION #2 = UNI-STRUT
OPTION #3 = THREADED ROD
57.4°
HOOD FRONT
OPTION #2
THE UNI-STRUT (U-CHANNEL) THAT HOLDS THE
HOOD UP CANTILEVERS OVER THE END OF
THE HOOD AND IS MOUNTED TO THE ASP
HANGER BRACKETS
END VIEW
"C" CLAMP
HOOD STANDING SEAM
HANGING CLIP BOLTED TO PLENUM SHELL
SUPPLY PLENUM SHELL
HOOD FRONT
8
Canopy Hood
OPTION #2
UNI-STRUT SUPPLIED BY OTHERS
TOP VIEW
HOOD
OPTION #1
FOR PLENUMS <= 96"
2 CLIPS ARE NEEDED
FOR PLENUMS > 96"
3 CLIPS ARE NEEDED
THE THIRD CLIP IS LOCATED
IN THE CENTER OF THE PLENUM
LENGTH
OPTION #1
ATTACH HANGING CLIP TO
HOOD STANDING SEAM WITH
THE SUPPLIED "C" CLAMPS
(OPTIONAL: DRILL AND BOLT A
1/4-20 SS BOLT THROUGH
THE CLIP AND HOOD STANDING
SEAM)
11.5
23.5
TOP VIEW
SUPPLY PLENUM
1.375 HANGER BRACKET
0.750
0.563
0.563
0.750
HANGING CLIP

Supply Plenum Clip

SUPPLY PLENUM SHELL
THREADED ROD
HOOD
OPTION #1
HANGING CLIP
HANGING CLIP
Using the Supply Plenum Clip
Note: The supply plenum is provided with
plenum clips that assist in hanging the plenum.
The plenum should not be hung only with the
plenum clips, threaded rod or uni-strut must
also be used.
1. Bolt the hanging clip to the supply plenum.
Two clips are needed for plenums less than
96 in. (243.84 cm) long and three for plenums
greater than 96 in. (243.84 cm). The third clip
is located in the center of the plenum length.
If there is a utility cabinet, the hanging clip
should be 23.5 in. (59.69 cm) from the end to
the hood.
2. Using the c-clamps provided, clamp the
supply plenum hanging clip to the hood
standing seam. Option: Drill and bolt a
1/4-20 SS bolt through the clip and hood
standing seam.
"C" CLAMP
HOOD FRONT
NOTE: SUPPLY PLENUMS ARE STANDARDLY SUPPLIED WITH HANGING CLIPS (OP
OPTION #3
THREADED ROD
SUPPLIED BY OTHERS
Using the Uni-strut
1. The uni-strut (supplied by others) that holds
the hood up cantilevers over the end of the
hood and is mounted to the supply plenum
hanger brackets.
Fig. 8
OPTION #1
HANGING CLIP COULD BE 23.5" FROM
END IF THERE IS A UTILITY CABINET
ON THE END OF THE HOOD
HANGING METHODS FOR SUPPLY PLENUMS
ASP, FSP AND VSP
OPTION #1 = HANGING CLIP
OPTION #2 = UNI-STRUT
OPTION #3 = THREADED ROD
THREADED ROD
OPTION #2
THE UNI-STRUT (U-CHANNEL) THAT HOLDS THE
HOOD UP CANTILEVERS OVER THE END OF
THE HOOD AND IS MOUNTED TO THE ASP
HANGER BRACKETS
END VIEW
HOOD
HOOD STANDING SEAM
HANGING CLIP BOLTED TO PLENUM SHELL
HANGING CLIP
SUPPLY PLENUM SHELL
IF OPTION #1 IS NOT APPLICABLE, USE OPTIONS 2 0R 3
OPTION #2
UNI-STRUT SUPPLIED BY OTHERS
TOP VIEW
HOOD
OPTION #1
FOR PLENUMS <= 96"
2 CLIPS ARE NEEDED
FOR PLENUMS > 96"
3 CLIPS ARE NEEDED
THE THIRD CLIP IS LOCATED
IN THE CENTER OF THE PLENUM
LENGTH
OPTION #1
ATTACH HANGING CLIP TO
HOOD STANDING SEAM WITH
THE SUPPLIED "C" CLAMPS
(OPTIONAL: DRILL AND BOLT A
1/4-20 SS BOLT THROUGH
THE CLIP AND HOOD STANDING
SEAM)
11.5
23.5
TOP VIEW
SUPPLY PLENUM
HANGER BRACKET
OPTION #3
THREADED ROD
SUPPLIED BY OTHERS
OPTION #1
HANGING CLIP
OPTION #1
HANGING CL
END IF THER
ON THE END
Fig. 7
®