Table of Contents
Advertisement
Camera Recording
(PV-L550/PV-L600/PV-L650/VM-L450)
Using the LCD Monitor
View recording scene on the LCD (Liquid
Crystal Display) monitor.
4
2
(PV-L650 shown)
1
POWER
5
VCR
CAMERA
OFF
3
Camera Recording (continued)
Easy Edit Stand-by
For a smooth transition between scenes if
recording is stopped, and then started within
24 hours.
POWER
VCR
CAMERA
OFF
1
4
,
2
Manual Easy Editing
For proper continuity when taping from Stop
mode or after attaching a new Battery.
STILL
C
PLAY
B
REW
FF
A
STOP
POWER
2
VCR
CAMERA
OFF
4
1
Before you begin...
Connect Camcorder to power source.
Insert cassette with record tab.
1
Press LCD-OPEN to unlock LCD
monitor.
2
Swing LCD monitor fully open and
adjust viewing angle.
Caution:
Rotating partially open LCD monitor
may block cassette door and damage
Camcorder body.
3
Set POWER to CAMERA.
LCD monitor turns on/off by the
POWER switch.
EVF shuts off when LCD monitor is
opened and turns back on when
LCD is closed.
Both EVF and LCD monitor turn on
when LCD is at 180 (see above
left).
This allows both you and the subject
to view the recording.
4
Turn BRIGHT control to adjust LCD
monitor brightness level.
5
Press RECORD/PAUSE to start
recording.
Note:
Using LCD monitor reduces battery operation
time.
Return LCD monitor to locked position when not
in use.
Before you begin...
Connect Camcorder to power source.
Insert cassette with record tab.
1
Press RECORD/PAUSE to stop
recording.
2
Set POWER to OFF and leave
cassette in Camcorder.
3
To resume recording, set POWER
to CAMERA.
4
Press RECORD/PAUSE to resume
recording.
Note:
Use Manual Easy Edit (below) if more than
24 hours before recording is resumed.
3
Before you begin...
Connect Camcorder to power source.
Insert cassette with record tab.
1
Set POWER to VCR.
2
A
Press REWIND/SEARCH to
rewind a few seconds of tape.
B
Press PLAY to review recording.
C
Press STILL where you want to
continue recording.
3
Set POWER to CAMERA.
4
Press RECORD/PAUSE to resume
recording.
3
Stand-by Quick Release
If left in RECORD/PAUSE mode for 5 minutes, Camcorder switches to Stand-by mode to
conserve battery. When set to ON, Stand-by Quick Release lets you resume recording by
pressing RECORD/PAUSE two times. New camcorders will default to OFF.
POWER
VCR
CAMERA
OFF
RECORD/
PAUSE
UP
DOWN
2
3
,
MENU
DISPLAY
Programmed Recording
Set a recording start and stop time. Or, set
a 5 or 10 second interval recording to be
done each minute.
UP
DOWN
1
2
3
,
,
MENU
DISPLAY
4
10MIN.
20MIN.
30MIN.
TO TAPE END
* 2
INTERVAL
INTERVAL
10 SEC/MIN.
5 SEC/MIN.
*1 Interval 5 SEC/MIN:
Record 5 seconds each minute.
*2 Interval 10 SEC/MIN:
Record 10 seconds each minute.
Note:
Start time may not be set over 24 hours
from current time.
Camcorder shuts off at tape end, or 12
hours after Interval Recording starts.
To cancel, set POWER to OFF.
Before you begin...
Connect Camcorder to power source.
Insert cassette with record tab.
1
Set POWER to CAMERA.
2
Press MENU for MENU mode.
Press UP
or DOWN
STAND-BY RELEASE
.
1
PROGRAMMED REC
TITLE
TALLY LAMP
STAND-BY RELEASE
CLOCK SET
SELECT : PUSH
SET
: PUSH DISPLAY KEY
END
: PUSH MENU KEY
3
Press DISPLAY to select ON/OFF.
4
,
ON: From Stand-by mode,
press RECORD/PAUSE two times
to resume recording.
OFF: From Stand-by mode,
set POWER to OFF, then to
CAMERA.
Press RECORD/PAUSE to record.
4
Press MENU to exit.
Before you begin...
¥
Connect Camcorder to power source.
Use AC Adaptor for longer recordings.
¥
Insert cassette with record tab.
¥
Set POWER to CAMERA.
1
Press MENU for MENU mode.
Press UP
or DOWN
PROGRAMMED
REC
.
2
Press DISPLAY. (Current time is
displayed.)
Each additional press of DISPLAY
increases start
time by 30
minutes.
3
Press DOWN
to select
TIME
. Press DISPLAY repeatedly to
select one of the options shown at
the left.
* 1
To cancel the setup, press MENU
twice.
4
Press RECORD/PAUSE to place
Camcorder in stand-by mode.
Recording will be done as scheduled.
to select
; AUTO/MANUAL
; ON
; OFF
KEY
to select
REC
Hide quick links:
Advertisement
Table of Contents
