Сombustion Area And Venting System Inspection; Regular Dealer Maintenance - Carrier 48GS Operating And Maintaining Manual

FILTER ACCESS
PANEL*
*For accessory filter rack.
Fig. 5 — Filter Access Panel — Vertical Supply Shown
Electrical Controls and Wiring —
trols are difficult to check without proper instrumentation;
therefore, if there are any discrepancies in the operating cycle,
contact your dealer and request service.
Refrigerant Circuit —
cult to check for leaks without the proper equipment; there-
fore, if inadequate cooling is suspected, contact your local
dealer for service.
Combustion Area and Vent System —
bustion area and vent system should be inspected visually
before each heating season. The normal accumulation of dirt,
soot, rust, and scale can result in loss of efficiency and im-
proper performance if allowed to build up.
If your unit makes an especially loud noise when the
main burners are ignited, shut down the heating section
and call your dealer.
Proceed as follows to inspect the combustion area and power-
venting system of your unit.
1. Turn off electrical power and gas supply to your unit.
2. Remove burner access panel. (See Fig. 1.)
3. Using a flashlight, carefully inspect the burner areas for
dirt, soot, rust, or scale. See Fig. 2.
If dirt, soot, rust, or scale accumulations are found,
call your dealer and do not operate your heating sec-
tion.
4. When you have completed your inspection, follow the
start-up procedures in this manual to restore your unit to
operation.
5. Observe unit heating operation.
ACCESS PANEL
Electrical con-
The refrigerant circuit is diffi-
The com-
Components in heat section may be hot after unit
has been started up. When observing flame, be care-
ful not to get close to or touch heating components
or serious personal injury may result.
Watch the burner flame to see if it is bright blue. If you
observe a suspected malfunction or if the burner flames
are not bright blue, call your dealer.
6. Replace burner access panel.
Unit Panels —
After performing any maintenance or serv-
ice on the unit, be sure all panels are fastened securely in
place to prevent rain from entering unit cabinet and to pre-
vent disruption of the correct unit airflow pattern.

REGULAR DEALER MAINTENANCE

In addition to the type of routine maintenance you might
be willing to perform, your unit should be inspected regu-
larly by a properly trained service technician. An inspection
(preferably each year, but at least every other year) should
include the following:
1. Inspection of all flue product passages — including the
burners, heat exchanger, and flue collector box.
2. Inspection of all combustion- and ventilation-air pas-
sages and openings.
3. Close inspection of all gas pipes leading to and inside of
your unit.
4. Inspection and, if required, cleaning of the condenser
and evaporator coils.
5. Inspection and, if required, cleaning of the evaporator
drain pan.
6. Inspection and cleaning of blower wheel housing and
motor.
7. Inspection of all supply-air and return-air ducts for leaks,
obstructions, and insulation integrity. Any problems found
should be resolved at this time.
8. Inspection of the unit base to ensure that no cracks, gaps,
etc., exist which may cause a hazardous condition.
9. Inspection of the unit casing for signs of deterioration.
10. Inspection of all electrical wiring and components to as-
sure proper connection.
11. Inspection for leaks in the refrigerant circuit. Pressure-
check to determine appropriate refrigerant charge.
12. Inspection of compressor oil level.
13. Operational check of the unit to determine working con-
ditions. Repair or adjustment should be made at this time.
Your servicing dealer may offer an economical service con-
tract that covers seasonal inspections. Ask for further
details.
Complete service instructions can be found in the unit
Installation, Start-Up and Service Instructions.
WARRANTIES
Units 48GS and GX have warranties located at the back
of this book. Be sure to read the warranty carefully to de-
termine the coverage for your unit.
6