Sharp 32R-S50 Service Manual page 10

32R-S50/S400,
36R-S50/S400,CR32S40
SERVICE
ADJUSTMENT ITEM
NUMBER
S01 PICTURE
S02 TINT
S03 COLOUR
S04 BRIGHTNESS
S05 SHARPNESS
S06 Vert. PHASE
S07 Hor. PHASE
S08 RF AGC
S09 Vert. AMPLITUDE
S10 PIF VCO
S11 R CUT-OFF
S12 G CUT -OFF
S13 B CUT-OFF
S14 G GAIN
S15 B GAIN
S16 TRAP
S17
S18 CC POSITION
S19 MUTE
S20 ENERGY SAVE OFFSET
S21 PERIOD ADJ.
S22 FAO VOLUME STEP
S23 TUNER
S24 FAV. COLOR RTONE-G
S25 FAV. COLOR RTONE-B
S26 FAV. COLOR BTONE-G
S27 FAV. COLOR BTONE-B
S28 COLOR TEMP LOW-G
S29 COLOR TEMP LOW-B
S30 COLOR TEMP ML-G
S31 COLOR TEMP ML-B
S32 COLOR TEMP HIGH-G
S33 COLOR TEMP HIGH-B
OP1 OPTION1
OP2 OPTION2
M01 INPUT LEVEL
M02 ST VCO
M03 FILTER
M04 WIDE BAND
M05 SPECTRAL
P01 PIP Y-LEVEL
P02 PIP TINT
P03 PIP COLOR
P04 PIP Y-OFFSET
P05 PIP H-POSITION
P06 PIP BGPM
P07 PIP FREERUN
Holding down both the VOL-up/CH-down buttons on the TV set at service mode for more than 2 seconds will
automatically write the above initial values into IC2101.
PART REPLACED
IC2001
IC201
IC2101
CRT
IC3001
IC1801
INITIAL VALUE
5E
46
32
40
28
00
12
23
20
2C
00
00
00
7F
7F
00
4B
17
00
20
7A
25
00
F9
EB
02
08
E1
AE
FA
E7
08
14
00
00
0A
20
1C
20
1B
30
29
2E
09
0A
00
0B
ADJUSTMENT
NECESSARY UNNECESSARY
X
X
X
X
X
X
DATA
RANGE
00-7F
00-7F
00-7F
00-7F
00-3F Must be set to "24"
00-07 Must be set to "00"
00-1F
00-3F
00-3F
00-7F
00-FF
00-FF
00-FF
00-FF
00-FF
00,01 Must be set to "01"
00-3F
00-FF
00,01,03 "00" : NORMAL, "01" : Y-MUTE, "03" : V-STOP & Y-MUTE
00-3F Must be set to "23"
00-FF Must be set to "7A"
00-32
00,01 Must be set to "00"
00-FF
00-FF
00-FF
00-FF
00-FF
00-FF
00-FF
00-FF
00-FF
00-FF
00-FF Must be set to "B1" for 32R-S50/36R-S50
Must be set to "B7" for 32R-S400/36R-S400/CR32S40
00-FF Must be set to "C7" for 32R-S50/36R-S50
Must be set to "E7" for 32R-S400/36R-S400/CR32S40
00-0F
00-3F
00-3F
00-3F
00-3F
00-7F
00-3F Must be set to "29" for 32R-S400/36R-S400/CR32S40
00-7F
00-1F Must be set to "09" for 32R-S400/36R-S400/CR32S40
00-FF Must be set to "0A" for 32R-S400/36R-S400/CR32S40
00-0F Must be set to "00" for 32R-S400/36R-S400/CR32S40
00-0F Must be set to "0B" for 32R-S400/36R-S400/CR32S40
Table - A
Data is stored in IC2101.
The adjustment is needed to compensate for characteristics of parts
including IC201 and MTS level (M01).
Holding down both the VOL-up/CH-down buttons on the TV set in the
service mode for more than 2 seconds will automatically write the
above initial values into IC2101. Then perform a complete adjustment.
Adjust items related to picture tube only.
Adjust items related to MTS only (M01~M05).
Adjust items related to P-IN-P only (P01~P07).
Table - B
10
ADJUSTMENT CONTENTS
NOTES