Page 2
Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor.
Removing and Installing a Power Supply Module Removing and Installing a Fan ... 4-6 FOX 4G Matrix 14400 • Table of Contents Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com..3-8 ... 4-1 .. 4-2...
About the FOX 4G Matrix 14400 All trademarks mentioned in this manual are the properties of their respective owners. 68-1539-50 Rev. A 12 08 FOX 4G Matrix 14400 • Table of Contents Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com.
RGB video, Digital Visual Interface (DVI) video, SDI/HD-SDI video, or low resolution video, depending on the transmitter and receiver. FOX 4G Matrix 14400 • Introduction Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. FOX 500 DVI Transmitter Multimode...
FOX 4G Matrix 14400 switcher, but you must ensure that you connect the proper transmission mode fiber cables to the board. FOX 4G Matrix 14400 • Introduction Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. FOX 4G Matrix 14400 Chapter Two Installation...
I/O board in location 17 - 32 are as follows: A = 17, B = 18, C = 19, D = 20, and so on. FOX 4G Matrix 14400 • Installation Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. Input Output...
Optical 2 connector on a FOX Tx transmitter. Output LED — This LED is always lit. Receiving FOX 4G Matrix 14400 • Installation Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. OPTICAL 1 2* Unit OPTIONAL FOR RETURN DATA...
See chapter 4, “Maintenance and Modifications”, to replace the power supply. FOX 4G Matrix 14400 • Installation Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. FOX 4G Matrix 14400 Chapter Three...
FOX 4G Matrix 14400 • Remote Control Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. ) commands that ™ , on pages 2-5 and...
Page 12
Command ASCII command (host to switcher) Create ties • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%. • The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%). N The & tie command for RGB and the % tie command for video can be used interchangeably. N The &...
Command ASCII command (host to switcher) Information requests Information request Request part number Request part number and Board configuration Query controller firmware version Example: = Inputs = Outputs X& = Board installed = Firmware version number to second decimal place (x.xx) Command ASCII command (host to switcher)
Launch.exe from the CD. Click the Software tab. Scroll to the Matrix Switchers program and click Install. FOX 4G Matrix 14400 • Remote Control Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. -based ® , and Starting the program Follow the on-screen instructions.
3-10 FOX 4G Matrix 14400 • Remote Control Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. Accessing the HTML Pages Another way to operate the switcher is via its factory-installed HTML pages, which are always available and cannot be erased or overwritten.
The switcher downloads the HTML start-up page. The switcher is ready for operation via HTML remote control. 3-12 FOX 4G Matrix 14400 • Remote Control Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. FOX 4G Matrix 14400 Chapter Four Maintenance and Modifications...
Slide the board or panel out of the chassis (next page). FOX 4G Matrix 14400 • Maintenance and Modifications Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. M OT LI NK...
If necessary, use a screwdriver to tighten the knurled knobs/captive screws. FOX 4G Matrix 14400 • Maintenance and Modifications Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. SI M O TE R EM...
If necessary, use a screwdriver to tighten the knurled knobs/captive screws. Secure the row identification plate to the fan. FOX 4G Matrix 14400 • Maintenance and Modifications Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com. M OT LI NK W ER...
Page 20
Maintenance and Modifications, cont’d FOX 4G Matrix 14400 • Maintenance and Modifications Refer also to the FOX 4G Matrix 14400 User’s Manual at www.extron.com.