Advertisement
Quick Links
WWW.WILLIAMS-REFRIGERATION.COM
SITE ASSEMBLY INSTRUCTIONS FOR MODULAR RUBY
IMPORTANT INFORMATION (PLEASE RETAIN THIS DOCUMENT)
This Manual covers the installation requirements for the following Williams Refrigeration products:
RMR1T
RMR2T
RMR3T
Please read this Manual carefully before installation.
Provided the instructions in this Manual are read and implemented correctly, the optimum performance and
reliability of your equipment should be maintained.
We assume the installer, user and service provider are appropriately trained, skilled and competent to
properly and safely carry out the work, and will use the necessary safety equipment, and take the necessary
precautions required of their intended work.
General Regulations
Declaration of Conformity:
Williams Refrigeration declares that all products manufactured by Williams Refrigeration comply with
the above directives applicable to those products, and those products are therefore declared to be in
conformity with the provisions of the above legislation.
Install Date.: ...............................................................................
Serial No.: ................................................................................
Advertisement
Related Manuals for Williams RMR1T
Summary of Contents for Williams RMR1T
- Page 1 WWW.WILLIAMS-REFRIGERATION.COM SITE ASSEMBLY INSTRUCTIONS FOR MODULAR RUBY IMPORTANT INFORMATION (PLEASE RETAIN THIS DOCUMENT) This Manual covers the installation requirements for the following Williams Refrigeration products: RMR1T RMR2T RMR3T Please read this Manual carefully before installation. Provided the instructions in this Manual are read and implemented correctly, the optimum performance and reliability of your equipment should be maintained.
-
Page 2: Important Safety Information
30mA. If the supply cord is damaged, it must be replaced by a service engineer or other qualified person. Only the supply cord supplied by Williams Refrigeration must be used. Fixed wiring appliances (those not supplied with a plug) shall incorporate a switch disconnector to meet the specification of IEC 60947;... -
Page 3: General Installation
The equipment must be correctly earthed. where restricted movement for installation and service is evident; therefore Williams Refrigeration Supplementary protective equipotential bonding recommend that this equipment be protected by an of the equipment may also be necessary, and if... - Page 4 INSTALLATION UNPACKING This is to be carried out by the installer, who will remove all interior and exterior packaging and accessories. NOTE TO THE INSTALLER: Stainless steel panels and doors are protected with plastic film when shipped. Prior to assembly, remove the film from any surfaces to be joined together and thoroughly clean the surfaces this exposed to remove any residue adhesive.
- Page 5 INSTALLATION - RMR1T - ROLL IN MODULAR RUBY INSTALLATION FOR A RMR1T - ROLL IN MODULAR RUBY INSTALLATION FIG 2. Site Preparation Please ensure that the floor area is clean and level. Lay the insulated floor or floor tray if supplied.
- Page 6 INSTALLATION - RMR1T - ROLL IN MODULAR RUBY Ensure all the walls and jambs have been located FOR THAW MODELS and camlocked together before lowering the roof Fit the duct to the rear wall, right hand side wall and section onto them.
- Page 7 INSTALLATION - RMR2T - ROLL IN MODULAR RUBY INSTALLATION FOR A RMR2T - ROLL IN MODULAR RUBY INSTALLATION FIG 2. Site Preparation Please ensure that the floor area is clean and level. Lay the insulated floor or floor tray if supplied. Models with a 15mm floor Put beads of food safe silicone sealant around the floor as shown before assembling the wall panels.
- Page 8 INSTALLATION - RMR2T - ROLL IN MODULAR RUBY FIG 5. Fit the roof angle to the jambs and roof using the screws provided. See ‘Fitting Roof Angle and Floor Plate’. Fit the floor angle if supplied and then fit the doors onto the door jamb by lowering vertically onto the hinges.
- Page 9 INSTALLATION - RMR2T - ROLL IN MODULAR RUBY FIG 10. FITTING FINISHING ANGLE (15MM FLOOR) Fit finishing angle with screws provided. See figure FIG 13. FOR THAW MODELS Using the screws provided, fit the air duct in the pre punched holes to the centre of the back wall and roof.
- Page 10 INSTALLATION - RMR2T - ROLL IN MODULAR RUBY FIG 15. Baffle shown fixed in position Fan Guard BULK HEAD LIGHT (OPTIONAL) Secure the bulk head light to the back of the door jamb legs with the screws provided. See figure 16. IMPORTANT: electrical connection of the bulk head light must only be carried out by a qualified, skilled and competent electrician.
- Page 11 INSTALLATION - RMR3T - ROLL IN MODULAR RUBY INSTALLATION FOR A RMR3T - ROLL IN MODULAR RUBY INSTALLATION FIG 2. Site Preparation Please ensure that the floor area is clean and level. Lay the insulated floor or floor tray if supplied. Models with a 15mm floor Put beads of food safe silicone sealant around the floor as shown before assembling the wall panels.
- Page 12 INSTALLATION - RMR3T - ROLL IN MODULAR RUBY FIG 5. FIG 8. FIG 6. Ensure all the walls and jambs have been located and camlocked together before lowering the roof section onto them. Please note that the roof is very heavy. See figure 9.
- Page 13 INSTALLATION - RMR3T - ROLL IN MODULAR RUBY FIG 10. FIG 12. Connect the door heaters if provided. IMPORTANT: electrical connection of the FITTING RAMPS heater must be carried out by a qualified, Fit the ramp to the front of the room with the screws skilled and competent electrician.
- Page 14 INSTALLATION - RMR3T - ROLL IN MODULAR RUBY FIG 14. BULK HEAD LIGHT Secure the bulk head light to the back of the door jamb legs with the screws provided. See figure 17. IMPORTANT: electrical connection of the bulk head light must only be carried out by a qualified, skilled and competent electrician.
-
Page 15: Panel Assembly
INSTALLATION - PANEL ASSEMBLY PANEL ASSEMBLY PANEL ASSEMBLY FINISHING Apply mastic or equivalent to the shaded areas To complete the installation, cap all the camlock before locking the wall panels together. keyholes with the plastic plugs provided. Do not cap the holes until you are satisfied that all the locks have been fully activated and the Ruby installation is complete and no adjustments are required. - Page 16 Fax: +852 2407 3767 www.williams-refrigeration.com.au sales@williams-hongkong.com www.williams-refrigeration.com.hk www.williams-refrigeration.com Williams Refrigeration is a trading name of AFE Group Limited. Registered in England & Wales under Registered Number 3872673. Registered Office Address - Bryggen Road, North Lynn Industrial Estate, King’s Lynn, Norfolk, PE30 2HZ 0560_OP_RUBY_INSTALL...