ADTRAN Total Access 300 Series Manual

Product P/N: 4187712G2
Surface Mounting Hole
Hinge
Security
Screw
Hinge
Fiber Optic
Cable
Ground
Fiber Drop
Ground Drop
D
ESCRIPTION
The Total Access ® 362S Single Family Unit (SFU) Optical Network
Terminal (ONT) is a Gigabit Passive Optical Network (GPON) ONT
with RF Overlay and Single Wire Return Device (SWRD) powering
(SFU ONT, P/N 4187712G2). The Total Access 300 Series has 2
POTS, and 2 Ethernet interfaces. The figure above illustrates the
SFU ONT inner enclosure. GPON technology provides a consistent
and common approach to advancing the public communications
network using:
♦
Traditional telephone service [Plain Old Telephone Service (POTS)]
♦
High speed data services (10/100/1000)
♦
Video services
♦
ETH 2
SWRD powering through
This Job Aid covers the electronics modules (SFU ONT) and housings
listed in the following table:
Total Access Description
362S
1187712G2 Total Access 362S Electronics Module
Total Access Description
SFU Housings
1187770G1 Total Access ONT Splice Housing
1187771G1 Total Access ONT with OptiTap Housing
NOTE
Refer to the Total Access 300 Series GigE SFU ONT with RF Overlay
and SWRD Powering Installation and Maintenance Guide (P/N
64187712G2-5) for more extensive installation instructions.
Total Access 300 Series
GigE SF ONT
with RF Overlay and SWRD Powering
Two-screw
Terminal
TIP RING
Bridges
TIP RING
TIP RING
FXS 0/1
FXS 0/2
TIP RING
POTS 2
TIP RING
TIP RING
ETH 1
ETH 2
ETH 0/1
ETH 0/2
SWRD Powering
Ethernet
Connections
CLEI
TEL. NUMBER
POTS Drop
RF Connection
Ethernet Drop
Surface
Mounting
Power
Hole
Ground and Power
Drop Callout
(10/100)
F P LED
RONT ANEL
Label Status
POWER
Off
Green
NETWORK
Green
STATUS
Yellow
Red
SWRD POWER
Off
(ETH 2)
Green
POTS 1 and 2
Off
Green
2
Green Flashing
ETH 1 and 2
Off
Green
Yellow Flashing
I
NSTALLATION
After unpacking the SFU ONT, inspect it for damage. If damage is noted,
file a claim with the carrier and then contact ADTRAN. For more infor‐
mation, refer to the warranty.
Required Tools and Supplies
Standard technician tools are used for installing SFU ONT. For a complete
list of special tools, supplies and test equipment, refer to the Total Access
300 Series GigE SFU ONT with RF Overlay and SWRD Powering Installation
and Maintenance Guide (P/N 64187712G2‐5).
Mount the Enclosure
Complete the following steps to mount the enclosure:
1. Choose a vertical surface near an approved ground, but away from
down spouts, permanent water sprinklers, or other water sources.
The subscriber should have easy access for testing.
2. Use the top and bottom external mounting holes as a template to
mark fastener locations. Use a level to ensure the unit is level to
prevent warping.
3. Pre‐drill the marked locations and install fasteners or anchors
appropriate to the mounting surface (each anchor rated to 15 lbs
minimum).
4. Mount the SFU ONT to the side of the subscriber's premise.
The Electronics Module is installed in the housing and swings open on
hinges. To release this module, loosen the Security Screw (refer to the
illustration on the first page) and swing the electronics Module to the left.
!
CAUTION
Do not use a knife to cut the opening in the rubber grommets. This may
result in an excessively large hole and compromise the integrity of the
unit allowing moisture into the unit.
jobAid
Issue Date: September 2010
Document P/N: 64187712G2-22C
S
Description
No power
Power is On
OLT has activated the ONT
OLT is discovering and ranging
The OLT has shut down the ONT
Power disabled
Power is On
Fiber is disconnected, GPON inter‐
face is down, or both ports are idle
or disabled
At lease one port is Off Hook
At least one port is Ringing
Link is down, no activity, or Admin‐
istratively Shut down
Link is up
TX or RX activity
1