Error Signals - Siemens DG30035E Installation And Operating Instructions Manual

Entering data and time
■
Press the multi-function rotary knob (3) and then select by
pressing the symbol;
■
Press the multi-function rotary knob to confirm.
The input options for day flash.
■
Turn the multi-function rotary knob (3) to select the correct
figure for the day and press to confirm.
The input for the month flashes on the display.
■
Turn the multi-function rotary knob (3) to select the correct
figure for the month and press to confirm.
■
The inputs for year, hours and minutes are undertaken in
the same way.
Note: After entry, the appliance automatically returns to the
previous operating mode (frost protection or heating mode).
Temperature setting in standard mode
The temperature can be set from 35–75 °C in 1 °C steps.
■
Press the multi-function rotary knob (3) and then select by
pressing the symbol;
■
Press the multi-function rotary knob to confirm.
lights up.
■
Turn the multi-function rotary knob (3) to select the
desired temperature and press to confirm.
The new temperature is saved. The appliance is once
again on standard mode.
Setting for holiday mode
The tank can be programmed so that it automatically
switches on at certain days and times. If the holiday setting
is activated, the tank is kept at a constant water temperature
of 10 °C.
■
Important: The date and time must already be set.
■
Press the multi-function rotary knob (3) and then select by
pressing the symbol;
■
Press the multi-function rotary knob to confirm, the
symbol lights up.
The input option for day flashes.
■
Turn the multi-function rotary knob (3) to select the day at
which the appliance should switch back on and press to
confirm.
The input option for month flashes.
■
Turn the multi-function rotary knob (3) to select the correct
figure for the month and press to confirm.
■
The inputs for year, hours and minutes are undertaken in
the same way.
■
After the entries are input, the appliance automatically
assumes the holiday mode.
The set start date and the starting time
alternately.
■
In addition to , the display indicates the setting which is
reactivated after the holiday program (
or timer mode).
■
LED (4) will light green.
10
starts to flash.
starts to flash.
starts to flash.
light up
standard mode
GB
Programming timer mode
The appliance can be programmed so that it can only be
heated up at a certain time (e.g. during low tariff times).
■
Important: The date and time must already be set.
■
Press the multi-function rotary knob (3) and then select by
pressing the symbol;
■
Press the multi-function rotary knob to confirm.
The symbol lights, the Start time can be entered.
The input option for hour flashes.
■
Turn the multi-function rotary knob (3) to select the hour
and press to confirm.
The minutes flash.
■
Turn the multi-function rotary knob (3) to select the minute
and press to confirm.
The symbol lights up.
■
Now the end time can be entered. Repeat the procedure
as for the start time.
Note: After entries are input, the appliance immediately and
automatically assumes the timer mode.
Info: If warm water is not required for an extended period, set
the tank to frost protection mode with button 6
The LED (4) lights red.
■
If the appliance is disconnected from the electrical
supply, the tank must be drained fully by our customer
service department or an authorised specialist in order to
avoid frost damage.
■
The device should be disconnected from the mains supply
when working on the water supply.

Error signals

■
Symbol flashes, message appears on display: E0
The heating is defective.
Contact customer service.
■
Symbol flashes, message appears on display: E1
The overheating protection has engaged.
Contact customer service.
■
Symbol flashes, message appears on display: E2
The anode is spent and must be replaced.
Customer service must be contacted as otherwise
corrosion prevention is no longer guaranteed.
The device can continue to be used for a very short time
with the "heat once" function.
■
Symbol flashes, message appears on display: E3
The temperature sensor is defective.
Contact customer service.
■
Symbol flashes, message appears on display: E4
The heating is defective.
Contact customer service.
starts to flash.