Table of Contents
Advertisement
Quick Links
UPFLOW/DOWNFLOW COILS
INSTALLATION INSTRUCTIONS
1. Important Safety Instructions
The following symbols and labels are used throughout this
manual to indicate immediate or potential safety hazards. It
is the owner's and installer's responsibility to read and comply
with all safety information and instructions accompanying
these symbols. Failure to heed safety information increases
the risk of personal injury, property damage, and/or product
damage.
HIGH VOLTAGE
DISCONNECT ALL POWER BEFORE SERVICING OR
INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY
BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY
DAMAGE, PERSONAL INJURY OR DEATH.
ONLY PERSONNEL THAT HAVE BEEN TRAINED TO INSTALL,
ADJUST, SERVICE OR REPAIR(HEREINAFTER, "SERVICE")
THE EQUIPMENT SPECIFIED IN THIS MANUAL SHOULD
SERVICE THE EQUIPMENT. THE MANUFACTURER WILL
NOT BE RESPONSIBLE FOR ANY INJURY OR PROPERTY
DAMAGE ARISING FROM IMPROPER SERVICE OR SERVICE
PROCEDURES. IF YOU SERVICE THIS UNIT, YOU ASSUME
RESPONSIBILITY FOR ANY INJURY OR PROPERTY
DAMAGE WHICH MAY RESULT. IN ADDITION, IN
JURISDICTIONS THAT REQUIRE ONE OR MORE LICENSES
TO SERVICE THE EQUIPMENT SPECIFIED IN THIS
MANUAL, ONLY LICENSED PERSONNEL SHOULD SERVISE
THE EQUIPMENT.
IMPROPER INSTALLATION, ADJUSTMENT, SERVICING OR
REPAIR OF THE EQUIPMENT SPECIFIED IN THIS MANUAL,
OR ATTEMPTING TO INSTALL, ADJUST, SERVICE OR REPAIR
THE EQUIPMENT SPECIFIED IN THIS MANUAL WITHOUT
PROPER TRAINING MAY RESULT IN PRODUCT DAMAGE,
PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
2. Shipping Inspection
Upon receiving the product, inspect it for damage from
shipment. Shipping damage, and subsequent investigation
is the responsibility of the carrier. Verify the model number,
specifications, and accessories are correct prior to installation.
The distributor or manufacturer will not accept claims from
dealers for transportation damage or installation of incorrectly
shipped units.
IO-4002
06/2021
WARNING
WARNING
19001 Kermier Rd, Waller, TX 77484
© 2021 Goodman Manufacturing Company, L.P.
2.1 Handling
Use caution when transporting / carrying unit.. Do not carry
unit with hooks or sharp object. The preferred method of
carrying the unit after arrival at the job site is to carry by
two-wheel hand truck from the back or sides or by hand
by carrying at the cabinet corners.
3. Codes & Regulations
This product is designed and manufactured to comply with
national codes. Installation in accordance with such codes
and/or prevailing local codes/regulations is the responsibility
of the installer. The manufacturer assumes no responsibility
for equipment installed in violation of any codes or regulations.
The United States Environmental Protection Agency (EPA)
has issued various regulations regarding the introduction and
disposal of refrigerants. Failure to follow these regulations
may harm the environment and can lead to the imposition
of substantial fines. Should you have any questions please
contact the local office of the EPA.
4. Replacement Parts
Inspect the unit to verify all required components are present
and intact. Report any missing components immediately to
the manufacturer or to the distributor. Make sure to include
the full product model number and serial number when re-
porting and/or obtaining service parts. Replacement parts for
this product are available through your contractor or local
distributor. For the location of your nearest distributor consult
the white business pages, the yellow page section of the local
telephone book or contact:
GOODMAN MANUFACTURING COMPANY, L.P.
5. Pre-Installation Instructions
5.1 Preparation
Keep this document with the unit. Carefully read all instruc-
tions for the installation prior to installing product. Make
sure each step or procedure is understood and any special
considerations are taken into account before starting instal-
lation. Assemble all tools, hardware and supplies needed
to complete the installation. Some items may need to be
purchased locally. Make sure everything needed to install
the product is on hand before starting.
www.goodmanmfg.com
HOMEOWNER SUPPORT
19001 KERMIER ROAD
WALLER, TEXAS 77484
877– 254 – 4729
Advertisement
Table of Contents
Related Manuals for Goodman UPFLOW
Summary of Contents for Goodman UPFLOW
- Page 1 The distributor or manufacturer will not accept claims from the product is on hand before starting. dealers for transportation damage or installation of incorrectly shipped units. IO-4002 19001 Kermier Rd, Waller, TX 77484 © 2021 Goodman Manufacturing Company, L.P. 06/2021 www.goodmanmfg.com...
- Page 2 DO NOT USE THE COIL PAN SHIPPED WITH THE UNIT ON OIL FURNACES OR ANY APPLICATION WHERE THE TMPERATURE CAPTA product line may be installed in upflow or downflow OF THE DRAIN PAN MAY EXCEED 300°F. A HIGH TEMPERATURE orientations.
-
Page 3: Refrigerant Lines
DO NOT over torque the 3/4” copper connector to the plastic BREAK AWAY drain connection. Using a wet rag or heatsink material on the short piece to protect the plastic drain pan, complete the drain line installation. Use Figure 2 as a template for typical drain pipe routing. - Page 4 LIQUID CAUTION LINE RUBBER APPLYING TOO MUCH HEAT TO ANY TUBE CAN MELT THE TUBE. GROMMET TORCH HEAT REQUIRED TO BRAZE TUBES OF VARIOUS SIZES MUST BE PROPORTIONAL TO THE SIZE OF THE TUBE. SERVICE LIQUID PERSONNNEL MUST USE THE APPROPRIATE HEAT LEVEL FOR LINE SET THE SIZE OF THE TUBE BEING BRAZED.
- Page 5 SATURATED SUCTION PRESSURE SATURATED LIQUID PRESSURE TEMPERATURE CHART TEMPERATURE CH ART SUCTION PRESSURE SATURATED SUCTION SATURATED LIQUID LIQUID PRESSURE PSIG R-22 R-410A TEMPERATURE ºF PSIG R-22 R-410A d. If subcooling is high and superheat is low, adjust TXV 10. Supply Duct Connection valve to 7 to 9 ºF superheat and remove charge to lower 1.
-
Page 6: Return Ductwork
11. Filler Plates Filler plates are supplied on all 17.5, 21, & 24.5 inch chassis to be used for adapting the unit to a furnace one size smaller. If the plenum and furnace openings are the same size, the FLANGE UNFOLDED UP filler plates must be removed. -
Page 7: Start-Up Procedure
Start-Up Procedure WARNING HIGH VOLTAGE DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. •. Prior to start-up, ensure that all electrical wires are properly sized and all connections are properly tightened. - Page 8 Air Handler / Coil Model Number Serial Number ELECTRICAL Line Voltage (Measure L1 and L2 Voltage) L1 - L2 Secondary Voltage (Measure Transformer Output Voltage) R - C Blower Amps Heat Strip 1 - Amps Heat Strip 2 - Amps BLOWER EXTERNAL STATIC PRESSURE Return Air Static Pressure IN.
- Page 9 THIS PAGE LEFT INTENTIONALLY BLANK...
- Page 10 THIS PAGE LEFT INTENTIONALLY BLANK...
- Page 11 THIS PAGE LEFT INTENTIONALLY BLANK...
-
Page 12: Customer Feedback
® For Product Registration, please register as follows: Daikin Products: (https://daikincomfort.com/owner-support/product-registration). Goodman® Brand products: (https://www.goodmanmfg.com/product-registration). Amana® Brand products: (http://www.amana-hac.com/product-registration). You can also scan the QR code on the right for the product brand you purchased to be directed to the Product Registration page.