IBM 7208 Setup And Operator Manual page 61

Hide thumbs Also See for 7208:

Service manual (92 pages)

Table Of Contents

Table of Contents

Appendix B. Fault Symptom Codes and Error Recovery Procedure Numbers

¦ DIAGNOSTIC

+-----------+------------------------------------+-----------+-----------¦

¦ Header in wrong format when

¦ loading ucode

+-----------+------------------------------------+-----------+-----------¦

¦ Control load image not valid

+-----------+------------------------------------+-----------+-----------¦

¦ EEPROM load image not valid

+-----------+------------------------------------+-----------+-----------¦

¦ Boot code old

+-----------+------------------------------------+-----------+-----------¦

¦ Cannot program one of the memories ¦

+-----------+------------------------------------+-----------+-----------¦

¦ CRC in load image was not correct

+-----------+------------------------------------+-----------+-----------¦

¦ Read buffer command failed

+-----------+------------------------------------+-----------+-----------¦

¦ Illegal position to format

¦ partition

+-----------+------------------------------------+-----------+-----------¦

¦ Partitions are too big for tape

+-----------+------------------------------------+-----------+-----------¦

¦ Partition format of tape failed

+-----------+------------------------------------+-----------+-----------¦

¦ Partition format aborted

+-----------+------------------------------------+-----------+-----------¦

¦ Failed position to a new partition ¦

+-----------+------------------------------------+-----------+-----------¦

¦ Partition switch aborted

+-----------+------------------------------------+-----------+-----------¦

¦ Software hang, we are very

¦ confused

+-----------+------------------------------------+-----------+-----------¦

¦ Software detects a hardware

¦ problem

+-----------+------------------------------------+-----------+-----------¦

¦ Detect PEOP

+-----------+------------------------------------+-----------+-----------¦

¦ Write Setmark failure

+-----------+------------------------------------+-----------+-----------¦

¦ WRITE failure after retry limit

¦ exceeded

+-----------+------------------------------------+-----------+-----------¦

¦ WFM failure after retry limit

¦ exceeded

+-----------+------------------------------------+-----------+-----------¦

¦ Write EOD failure after retry

¦ limit exceeded

+-----------+------------------------------------+-----------+-----------¦

¦ Fill error, invalid BRT

+-----------+------------------------------------+-----------+-----------¦

¦ Fill error, buffer empty

+-----------+------------------------------------+-----------+-----------¦

¦ Deformatter interrupt timeout on

¦ search

+-----------+------------------------------------+-----------+-----------¦

¦ Overwrite (bad readback; check

¦ block type)

+-----------+------------------------------------+-----------+-----------¦

¦ Formatter interrupt timeout on

¦ WRITE

+-----------+------------------------------------+-----------+-----------¦

¦ Permanent write error, write

¦ recovery fail

+-----------+------------------------------------+-----------+-----------¦

¦ Permanent write error rewrite

¦ threshold

+-----------+------------------------------------+-----------+-----------¦

7208 Tape Drive Setup and Operator Guide

8,6

¦ Copyright IBM Corp. 1998

B.0 - 3

T = 100% ¦

D = 100% ¦

T = 100% ¦

D = 100% ¦

D = 50%

O = 50%

O = 100% ¦

T = 100% ¦

D = 5%

O = 90%

S = 5%

T = 100% ¦

D = 5%

O = 90%

S = 5%

D = 100% ¦

A = 100% ¦

T = 100% ¦

D = 30%

T = 70%

D = 30%

T = 70%

D = 30%

T = 70%

D = 100% ¦

D = 50%

T = 50%

D = 100% ¦

D = 30%

T = 70%

D = 30%

T = 70%

D = 30%

Table of Contents

This manual is also suitable for:

342

IBM 7208 Setup And Operator Manual page 61

Related Manuals for IBM 7208

Related Products for IBM 7208

This manual is also suitable for:

Table of Contents