Status Light - IBM 7208 Setup And Operator Manual

3.2.2 Status Light

Three status lights 4 and their ISO symbols appear on the 7208 Tape Drive as follows:
The combinations of the lights and their definitions are shown in Figure 8.
+------------------------------------------------------------------------+
¦ Figure 8. Status Lights on the 7208 Tape Drive
+------------------------------------------------------------------------¦
¦ Status Lights ¦ Status
+-----------------+------------------+-----------------------------------¦
¦ PICTURE 13 ¦
¦ Fault ¦ On
+-----------------+------------------¦
¦ PICTURE 14 ¦ On
¦ Ready ¦
+-----------------+------------------¦
¦ PICTURE 15 ¦
¦ Activity ¦ On
+------------------------------------------------------------------------¦
+------------------------------------------------------------------------¦
¦ PICTURE 16 ¦
¦ Fault ¦ Off or On
+-----------------+------------------¦
¦ PICTURE 17 ¦ Off
¦ Ready ¦
+-----------------+------------------¦
¦ PICTURE 18 ¦ Off
¦ Activity ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
+------------------------------------------------------------------------¦
+------------------------------------------------------------------------¦
¦ PICTURE 19 ¦
¦ Fault ¦ Off or On
+-----------------+------------------¦
¦ PICTURE 20 ¦ Off
¦ Ready ¦
------------------+------------------¦
¦ PICTURE 21 ¦ Flashing or Off
¦ Activity ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
¦ ¦
+------------------------------------------------------------------------¦
+------------------------------------------------------------------------¦
¦ PICTURE 22 ¦
¦ Fault ¦ Flashing
+-----------------+------------------¦ corrective action:
¦ PICTURE 23 ¦ Off or On
¦ Ready ¦
------------------+------------------¦
¦ PICTURE 24 ¦ Off, On, or
¦ Activity ¦ Flashing
¦ ¦
¦ ¦
¦ ¦
¦ ¦
7208 Tape Drive Setup and Operator Guide
Status Light
¦ Status of 7208 Tape Drive
¦ The Power-On Self Test (POST) is
¦ running.
¦
¦
¦
¦
¦ One of the following conditions
¦ exists:
¦ The power is off (Fault light ¦
¦ is off).
¦ The POST has completed
¦ successfully, but no tape
¦ cartridge has been inserted.
¦ If the Fault light is on,
¦ cleaning is required. See
¦ "Cleaning the Tape Drive" in
¦ topic 3.6.
¦ A tape cartridge has been
¦ inserted:
¦ The 7208 Tape Drive is ready
¦ to receive commands from the
system (whether the Fault
¦ light is on or off).
¦
¦ If the Fault light is on,
¦ cleaning is required. See
¦ "Cleaning the Tape Drive" in
¦ topic 3.6.
¦
¦ If the Activity light
¦ flashes, a tape cartridge is
¦ in the drive and tape
¦ movement is occurring. If the ¦
¦ light is off, no tape
¦ movement is occurring.
¦ The 7208 Tape Drive has detected
¦ an internal fault that requires
¦
¦ Reset the error by turning
the power off to the 7208
¦ Tape Drive, then turning it
¦ back on, or by holding down
¦ the unload button for about
¦ 15 seconds.
¦
¦ If the Fault light still
¦ Copyright IBM Corp. 1998
3.2.2 - 1
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦
¦