Test Mode - Sony STR-DG500 Service Manual

STR-DG500/DG600
FACTORY PRESET MODE
* All preset contents are reset to the default setting.
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the
[MOVIE] buttons simultaneously, press the
on the main power.
The message "FACTORY" appears for a moment and the present
contents are reset to the default values.
AM CHANNEL STEP 9 kHz/10 kHz SELECTION
MODE (US, Canadian, E2 model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the
button to turn off the main power.
?/1
While depressing the [TUNING MODE] button, press the
button to turn on the main power.
Either the message "9k STEP" or "10k STEP" appears for a
moment and select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same
time, then each segment lights on one after another.
* Procedure:
While depressing the [TUNING MODE] and the [DISPLAY] but-
tons simultaneously, press the
power.
1. ALL segments light on.
LFE SP A D D DIGITAL EX D D PRO LOGIC II x DTS-ES NEO:6
SW
SP B SLEEP OPT COAX
L C R
SL S SR
SBL SB SBR
[MULTI CHANNEL DECODING] LED light on.
2. Turn the [INPUT SELECTOR] control, confirm display.
LFE A EX
SW
SLEEP COAX
L R
S
SB
3. Turn the [INPUT SELECTOR] control, confirm display.
SP DIGITAL PRO LOGIC
D D D D
SP B OPT
C
SL SR
SBL SBR
[MULTI CHANNEL DECODING] LED light on.
4. Turn the [INPUT SELECTOR] control, all segments and all LEDs
light off.
14
All manuals and user guides at all-guides.com
SECTION 3

TEST MODE

button to turn
?/1
?/1
?/1 button to turn on the main
AAC CAT RDS
MEMORY
HDMI 96/24 D.RANGE EQ STEREO MONO A.DIRECT
dB
k Hz
m ft.
MHz
II DTS NEO:6 CAT
MEMORY
96/24 D.RANGE STEREO
dB
Hz
ft.
x -ES AAC RDS
HDMI EQ MONO A.DIRECT
k
m
MHz
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon
completion of repair.
* Procedure:
While depressing the [2CH] button, press the
on the main power.
The message "S.F. CLR." appears for a moment and initializa-
tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the
[DISPLAY] buttons simultaneously, press the
on the main power.
The model name, destination and the software version are dis-
played for a moment.
KEY CHECK MODE
* Button check
* Procedure:
While depressing the [SPEAKERS $OFF/A/B/A+B%] and the [2CH]
buttons simultaneously, press the
power.
Either the message "REST 13" (STR-DG500) or "REST 14"
(STR-DG600) appears.
Every pressing of any button other than the
the buttons. The buttons which are already counted once are not
counted again. When all buttons are pressed "REST 00" appears.
AUTOBETICAL MODE (AEP, UK model only)
* When this mode is used, the receiver scans the broadcasts that
can be received by the tuner, and sets up the broadcasts.
Be sure to start scanning after connecting the antenna.
* Procedure:
Check that the antenna is connected.
While depressing the [MEMORY/ENTER] button, press the
button to turn on the main power.
The message "AUTO-BETICAL SELECT" appears for a mo-
ment and the receiver starts scanning.
COMMAND MODE SELECTION MODE
* The command mode (AV1 or AV2) of the remote commander
can be selected.
* Procedure:
While depressing the [INPUT MODE] button, press the
ton to turn on the main power.
Either the message "C.MODE.AV 1" or "C.MODE.AV 2" ap-
pears for a moment and select the desired mode.
button to turn
?/1
?/1 button to turn
button to turn on the main
?/1
?/1 counts down
?/1
but-
?/1