An Error Message Appears On The Screen - Canon i350 Quick Start Manual

An Error Message Appears on the Screen

Problem Possible Cause
Printer not ready
Error Writing /
Output to USBxxx
Paper is not loaded Load paper and press the RESUME/CANCEL
Faulty connection
Printer port error
Printer port
settings and printer
interface do not
match
Printer driver is not
installed properly
Not enough
memory
"Error No.: X202"
Printer driver fault
"Error No.: X203"
Printer not ready
"Error No.: X300"
Printer not properly
connected
Printer not selected
in Chooser
The POWER POWER POWER lamp will flash green when the printer is warming up or when a print POWER
job is being sent to the printer. It will glow a steady (non-flashing) green when it
is ready for use or when the print job is completed.
Ensure that the printer cable is securely connected to the computer.
Note If you are using a switching hub or other device, disconnect the
printer and reconnect it directly to the computer and try
printing again.
If successful, the problem may have been with the device.
There could also be a problem with the cable(s). Replace the
cable(s) and try printing again.
Verify the printer port status.
Double-click Universal Serial Bus (USB) controllers Universal Serial Bus (USB) controllers on the Device Manager Universal Serial Bus (USB) controllers Universal Serial Bus (USB) controllers
dialog box, then double-click Canon i350
Refer to the User's Guide for instructions on how to verify the status.
Confirm that the destination Printer Port is set to USB PRNnn (Canon i350/
Canon i250) or USBnn (Canon i350/Canon i250 Canon i250 Canon i350/Canon i250) (where nn represents a
Canon i250 Canon i250 Canon i350/Canon i250 Canon i350/Canon i250
number).
If the settings are not correct, follow the procedures described in the
Instructions
and reinstall the printer driver.
User's Guide
Refer to the for instructions on how to verify status and the correct
action to take.
Uninstall then reinstall the printer driver.
1. Click Start Start Start Start, and select All Programs All Programs All Programs (or Programs All Programs
and Uninstall Uninstall.
Uninstall Uninstall
2. Follow the on-screen instructions to uninstall driver.
3. Follow the procedures described in the
the printer driver.
Increase available memory by closing any other applications currently running.
Uninstall, then reinstall the printer driver.
Refer to the User's Guide for instructions on how to uninstall the printer driver.
If the POWER POWER POWER lamp is off, turn the printer on. POWER
If the POWER POWER lamp is flashing green, the printer is initializing. Wait until the
POWER POWER
POWER lamp stops flashing. POWER POWER POWER
Ensure that the printer is securely connected to the computer.
Note If you are using a switching hub or other device, disconnect
the printer and reconnect it directly to the computer and try
printing again.
If successful, the problem may have been with the device.
There could also be a problem with the cable(s). Replace the
cable(s) and try printing again.
1. From the Apple Apple menu, select Chooser Apple Apple
2. Click the i350/i250 i350/i250 icon and ensure that the i350/i250 is selected as the
i350/i250 i350/i250
target connection. If not, select it.
Note If the problem persists, delete all unnecessary documents
from the Extensions and Control Panels folder.
Try This
RESUME/CANCEL button.
RESUME/CANCEL RESUME/CANCEL
Canon i350/Canon i250 Canon i350 Canon i350 Canon i250 to see the status. Canon i250 Canon i250
Programs Programs), Canon i350/Canon i250 Programs
Easy Setup Instructions
Chooser Chooser. Chooser
Troubleshooting
Device Manager Device Manager Device Manager
Canon i350/
Canon i350/ Canon i350/
Easy Setup
Canon i350/Canon i250, Canon i350/Canon i250 Canon i350/Canon i250
and reinstall
47