Page 1 This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2). For (*1) and (*2), refer to GREEN PRODUCT PROCUREMENT LEAD-FREE SOLDER. © TOSHIBA CORPORATION file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.292\32W... 02.05.2015...
Page 2: Green Product Procurement
Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.
Page 3: Lead-Free Solder
Стр. 1 из 1 LEAD-FREE SOLDER This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product. WARNING: This product is manufactured using lead free solder.
Page 4: Important Notice
Through WEB, ver. 6.5 has been released but with it, the linking function in this manual may not work properly. If ver. 6.5 has been installed, uninstall it and reinstall ver. 6.0. To get ver. 6.0, click the icon, or contact to the nearest Toshiba Service Centre for further assistance. Freezing windows opened (Cannot close the open windows) This may happen occasionally.
Page 5 Стр. 2 из 2 Continue to use by operating the windows. Precaution when opening the diagrams While opening the diagrams, the menu in the left frame changes its color to GRAY. This is an indication that the viewer is processing. With this condition, the menu indication color may stick to the GRAY color or Windows may freeze if clicking other menu.
Page 6 Стр. 1 из 4 IMPORTANT NOTICE User Guide Autodesk® DWF™ Viewer is necessary to view drawings and to activate the functions of this system. Please download and install. When Windows XP SP2 is used, pop-up windows are limited by the enhanced security function and this sample may not work.
Page 7: Operating Environment
Стр. 2 из 4 Operating Environment : Pentium III or higher recommended Monitor : 1024 x 768 or higher resolution recommended file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.764\32W... 02.05.2015...
Page 8 Стр. 3 из 4 Mouse : A mouse with wheel recommended : Microsoft Windows 2000/XP Browser Microsoft Internet Explorer 6.0 or later Drawing viewer : Autodesk DWF Viewer 6.0 * Use the software following respective license terms and conditions. Note: In case of using this service manual with network connection, allocate its folder to the client PCs as network drive to avoid any possible malfunction.
Page 9 Стр. 4 из 4 Layer Display Changing Function When any of the color buttons on the toolbar is clicked, it can be selected to display desired layer in its color or not to display each layer. This allows you to see the pattern layer only by setting other layers to "non-display".
Page 10 WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Toshiba shall not be liable for any damages, losses, expenses or costs, if any, incurred in connection with or as a result of use of any information or data provided herein.
Page 11: Service Mode
Стр. 1 из 18 ADJUSTMENT Service Mode Entering to Service Mode 1. Set VOLUME to minimum and press button once on remote control. ↓ ↓ ↓ ↓ 2. Press button again and hold button down. ↓ ↓ ↓ ↓ Service Mode display 3.
Page 12 Стр. 2 из 18 Displaying the Adjustment Menu Press MENU button on TV. Service Mode Press ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ Press Adjustment Mode Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC.
Page 13: Setting & Adjusting Data
Стр. 3 из 18 Test signal selection Selection of the adjustment items (on TV or remote control) Change of the data value Volume +/- (on TV or remote control) Adjustment menu mode ON/OFF MENU button (on TV) Initialization of the memory (QA02) CALL + CH button on TV ( Reset the count of operating CALL + CH button on TV (...
Page 14 Стр. 4 из 18 Item Name of adjustment RCUT R CUT OFF GCUT G CUT OFF BCUT B CUT OFF RDRV R DRIVE GDRV G DRIVE BDRV B DRIVE BRTC BRIGHTNESS CENTER COLC COLOR CENTER UVTT BASE BAND TINT CNTX CONTRAST MAX VOLUX MAX VOLUME LIMITED PLLW0 PLL WAIT TIME...
Page 15: Function Description
Стр. 5 из 18 FPLG2 Channel LOGO Vector Clip SW (SD) FPLG3 Channel LOGO Vector Clip SW (HD) Factory preset data will be loaded after setting Model ID data. (Refer to Initialization of Memory Data of QA02 and setting data of signal board.) Adjusting the Data Pressing of VOLUME +/- button will change the value of data in the range from 00H to...
Page 16 Series Model name Panel vendor OPT4 value OPT5 value WL68 EU Ready 32WL68P 0x45 0x11 37WL68P 0x46 0x11 EU/UK Digital 32WLT68 0x45 0x11 37WLT68 0x46 0x11 42WLT68 0x47 0x11 Ex. OPT4 value 0xB7 is for 42 inches CMP made 1080p panel.
Page 17: Exit From Service Mode
Стр. 7 из 18 OPT5 (bit7) (bit6) (bit5) (bit4) (bit3) (bit2) (bit1) (bit0) AUO Panel PMVA AMVA 100 Hz Drive Panel WXGA Resolution 1080p Exit from Service Mode Pressing POWER button to turn off the TV once. Initialization of Memory Data of QA02 and setting data of signal board. After replacing QA02 or signal board, the following initialization is required.
Page 18 8) Set I2C check function of TVOP to enable. 9) Check the picture carefully. If necessary, adjust any adjustment item above. Perform "Auto tune" on the ownerЃfs manual. Europe MODEL ID (HEX) Model name Panel vender 0x01 32WLT68 0x02 37WLT68 0x03 42WLT68 0x04 32WL68P...
Page 19: Test Signal Selection
Стр. 9 из 18 0x19 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x30 0x31 0x32 0x33 Test Signal Selection Every pressing of button on the remote control changes the built-in test patterns on screen as described below in Service Mode. Picture Signal Red raster...
Page 20: Self-Diagnostic Function
Стр. 10 из 18 Green raster Blue raster All Black All White Self Diagnostic Function 1. Press "9" button on remote control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC's is executed properly. 2.
Page 21 Стр. 11 из 18 (3) Bus line : -- "OK" is normal SCL-GND (Red indication) : SCL-GND short circuit SDA-GND (Red indication) : SDA-GND short circuit SCL-SDA (Red indication) : SCL-SDA short circuit (4) Bus cont : --- "OK" is normal. NG is abnormal (Red indication).
Page 22 Стр. 12 из 18 1. Press "9" button twice on remote control during display of adjustment menu in the service mode. The version of main MPU will be checked. 2. During Version Check, the following displays are shown. (1) MAIN MPU : Version information of microprocessor Series name and Code Program Version (4 figure number) and OSD Version (2 figure number).
Page 23 Стр. 13 из 18 (7) MW Ver Version information of DB software middleware. (Only digital model) (8) A/D Adjust A/D adjustment item. --MAIN : It's enable only in double Window model. A/D adjustment status of main picture. --PIP : It's enable only in double Window model. A/D adjustment status of sub picture.
Page 24: Screen Size
Стр. 14 из 18 The status of this model will be checked. 2. During Status Check, the following displays are shown. (1) MAIN : Main source information : Display RF position number (0 - 99) on the main screen, or Input Source (EXT1/2/3/HDMI etc.) (2) MAIN FORMAT : Display Video and PC format information...
Page 25 Стр. 15 из 18 Super Live 2 Cinema 2 Super Live 1 Cinema 1 Subtitle 14:9 Note: Exact Scan is shown only for 1080p panel model with video input mode except pc. (8) OTHER STATUS : Other status information : Display three numbers of 2 byte data. Setting Hotel Mode Enter to service mode and select Hotel Mode menu by pressing P or P .
Page 26 Стр. 16 из 18 D2 (bit2) Disable SET UP MENU except Disable Enable language. (Display the language only) (tuning SETUP MENU) D1 (bit1) Disable SETUP MENU Disable Enable D0 (bit0) HOTEL Mode On (Enable the setting of D1 from to D7) (Normal) VOLUX Set VOLUX as following.
Page 27: Led Indication
Стр. 17 из 18 D6 (bit6) ~ Forced speaker volume 0 ~ 100 [decimal] (Normal: 0) D0 (bit0) Value above 100 is no effect. OPT8 FUNCTION DESCRIPTION 0 (Normal) D7 (bit7) ~ - (no use) D3 (bit3) D2 (bit2) Enable mode that picture mode will be set in Enable Disable forced when turn ON the main power...
Page 28 Стр. 18 из 18 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.960\32W... 02.05.2015...
Page 29: Function And Operation
Стр. 1 из 1 FUNCTION AND OPERATION The Remote Control Simple at-a-glance reference of your remote control. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.389\32W... 02.05.2015...
Page 30 Стр. 1 из 2 FUNCTION AND OPERATION Control and Input Connection A wide variety of external equipment can be connected to the input sockets on the side of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions.
Page 31 Стр. 2 из 2 Using the Control and Connection file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.574\32W... 02.05.2015...
Page 32: Tuning The Television For The First Time
Стр. 1 из 3 FUNCTION AND OPERATION Tuning the Television for the First Time Before switching on the television put your decoder and media recorder to Standby if they are connected and ensure the aerial is connected. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.925\32W... 02.05.2015...
Page 33 Стр. 2 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.925\32W... 02.05.2015...
Page 34 Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.925\32W... 02.05.2015...
Page 35: Digital Auto Tuning
Стр. 1 из 3 FUNCTION AND OPERATION Digital Auto Tuning Note: As new services are broadcast it will be necessary to re-tune the television in order to view them. Auto Tuning file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.994\32W... 02.05.2015...
Page 36 Стр. 2 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.994\32W... 02.05.2015...
Page 37 Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.994\32W... 02.05.2015...
Page 38: Digital Programme Sorting, Manual Tuning
Стр. 1 из 3 FUNCTION AND OPERATION Digital Programme Sorting, Manual Tuning Note: When the television is switched off the mode being viewed at the time will automatically be selected when the television is switched back on. Programme Sorting file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.749\32W... 02.05.2015...
Page 39 Стр. 2 из 3 Manual Tuning file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.749\32W... 02.05.2015...
Page 40 Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.749\32W... 02.05.2015...
Page 41 Стр. 1 из 3 FUNCTION AND OPERATION Tuning Analogue Mode for the First Time The Quick Setup feature will tune all analogue channels currently available in the area. To put the television into ATV mode press and hold then use to highlight ATV.
Page 42 Стр. 2 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.012\32W... 02.05.2015...
Page 43 Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.012\32W... 02.05.2015...
Page 44 Стр. 1 из 5 FUNCTION AND OPERATION Analogue Manual Tune The television can be tuned-in manually using Manual tuning. For example: if the television cannot be connected to a media recorder/decoder with a SCART lead or to tune-in a station on another System.
Page 45 Стр. 2 из 5 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.804\32W... 02.05.2015...
Page 46 Стр. 3 из 5 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.804\32W... 02.05.2015...
Page 47 Стр. 4 из 5 Using Auto Tuning file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.804\32W... 02.05.2015...
Page 48 Стр. 5 из 5 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.804\32W... 02.05.2015...
Page 49 Стр. 1 из 3 FUNCTION AND OPERATION Analogue Programme Skip, Sorting Programme Position Programme Skip file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.495\32W... 02.05.2015...
Page 50 Стр. 2 из 3 Sorting Programme Position file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.495\32W... 02.05.2015...
Page 51 Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.495\32W... 02.05.2015...
Page 52: Safety Instruction
Handling the LCD Module Стр. 1 из 4 SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 53 Handling the LCD Module Стр. 2 из 4 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 54 Handling the LCD Module Стр. 3 из 4 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 55 Handling the LCD Module Стр. 4 из 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.625\32W... 02.05.2015...
Page 56 LOWB POWER VESTEL DB AV TERM FRONT HDMI SIGNAL 100...
Page 57: Safety Precaution
SAFETY INSTRUCTION [LCD] ASIA, EU Стр. 1 из 4 SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 58 SAFETY INSTRUCTION [LCD] ASIA, EU Стр. 2 из 4 inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7.
Page 59 SAFETY INSTRUCTION [LCD] ASIA, EU Стр. 3 из 4 Resistance values in orms ( ). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
Page 60: Product Safety Notice
SAFETY INSTRUCTION [LCD] ASIA, EU Стр. 4 из 4 Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 61: Specification
Стр. 1 из 2 SPECIFICATION file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.852\32W... 02.05.2015...
Page 62 Стр. 2 из 2 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.852\32W... 02.05.2015...
Page 77 Digital receiving board SIGNAL BOARD AV BOARD PANEL DDR RAM DDR RAM FLI8668 CORTEZ Advance VBI Data Processor PANEL I/F DCDi Input Video Analog MADi Terminal Decoder Front Scaling (Audio) (16port) LVDS CVBS(L/R) S-VIDEO(L/R) YCbCr(L/R) Channel SCART(L/R) Standby Process uCON Digital Input A EEPROM...
Page 78: Schematic Diagram
Стр. 1 из 2 SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit...
Page 79 Стр. 2 из 2 All capacitors are ceramic 50 V, unless otherwise noted as the following marks. = Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4.
Page 170 Accessory Стр. 1 из 1 Accessory Location Parts No. Description Y101 75004340 MANUAL, MANUAL(ENGLISH) Y101E 75004342 MANUAL, MANUAL(EURO) Y110 75004341 MANUAL, QSUG Y114 75004343 MANUAL, SCHEMATIC DIAGRAM Y130 75002113 REMOCON HAND UNIT, CT-8002 Y170 23845800 HOLDER, WIRE, NYLON66 D6.8 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.799\32W... 02.05.2015...
Page 171 Cabinet Стр. 1 из 1 Cabinet Location Parts No. Description A201 75004326 CABINET/RACK FRONT BEZEL ASSY A315 75004405 SUPPORT/HOLDER PIECE C COVER ASSY A330 75004347 SUPPORT/HOLDER PIECE AC HOLDER A340 75004348 BRACKET PIECE CONTROL S ASSY WL68 A375 23717240 SCREW, BITTB3X10SZN A380 23717240 SCREW, BITTB3X10SZN...
Page 172 Miscellaneous Стр. 1 из 1 Miscellaneous Location Parts No. Description B001 75004322 DISPLAY G6AUO32V6, T315XW02 V6 H001 23321550 TUNER, ENGF7304GF P801 23372353 POWER CORD, UK 250V3A FL/FUSE13 P801 23372298 POWER CORD, 250V2.5A PJ22B 75002683 CONNECTOR, 1MM PITCH B TO B, 237702150K4 PP21 23974994 BAND, KESSOKU...
Page 173 Packing Стр. 1 из 1 Packing Location Parts No. Description A701A 75004331 CARTON CASE, CASE A701B 75004337 CARTON BOTTOM CASE, BOTTOM CASE A702A 75004332 CARTON TOP PACKING, TOP PACKING A702B 75004333 PAD BOTTOM PACKING, BOTTOM PACKING A703 75004335 PACKING MATERIAL HOGOBUKURO, HOGOBUKURO A705 23518043 PACKING, JOINT, 32Z5P...
Page 174: Parts List
Стр. 1 из 2 PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit...
Page 175 Стр. 2 из 2 : Electrolytic : Metal Film : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa1.524\32W... 02.05.2015...
Page 176 U01AS SIGNAL (PE0194) Стр. 1 из 6 Loading ... Location Parts No. Description U01AS 75004488 PC BOARD ASSY, PE0194A1, SIGNAL C311 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C312 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C313 V03GD0000559 CHIP CERAMIC CAPACITOR (1608) C360 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C361 V03GD0001318 CHIP CERAMIC CAPACITOR (2012) C362...
Page 177 U01AS SIGNAL (PE0194) Стр. 2 из 6 C427 V03GD0001318 CHIP CERAMIC CAPACITOR (2012) C428 V03GD0001144 CHIP CERAMIC CAPACITOR (1608) C429 V03GD0001318 CHIP CERAMIC CAPACITOR (2012) C430 V13GD0000338 CHIP THREE TERMINAL CAPACITOR C431 V03GD0001318 CHIP CERAMIC CAPACITOR (2012) C432 V03GD0001144 CHIP CERAMIC CAPACITOR (1608) C433 V03GD0001144 CHIP CERAMIC CAPACITOR (1608) C434...
Page 178 U01AS SIGNAL (PE0194) Стр. 3 из 6 C777 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C778 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C779 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C780 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C781 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C782 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C783 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C784...
Page 179 U01AS SIGNAL (PE0194) Стр. 4 из 6 C2019 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3001 V03GD0001318 CHIP CERAMIC CAPACITOR (2012) C3002 V03GD0001320 CHIP CERAMIC CAPACITOR (3216) C3003 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3004 V03GD0001320 CHIP CERAMIC CAPACITOR (3216) C3005 V03GD0000589 CHIP CERAMIC CAPACITOR (1608) C3006 V03GD0001318 CHIP CERAMIC CAPACITOR (2012) C3007...
Page 180 U01AS SIGNAL (PE0194) Стр. 5 из 6 C3041 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3042 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3043 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3044 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3045 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3046 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3047 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C3048...
Page 181 U01AS SIGNAL (PE0194) Стр. 6 из 6 C5005 V03GD0000572 CHIP CERAMIC CAPACITOR (1608) C5006 V03GD0000538 CHIP CERAMIC CAPACITOR (1608) C5007 V03GD0000538 CHIP CERAMIC CAPACITOR (1608) C5008 V03GD0000538 CHIP CERAMIC CAPACITOR (1608) C5009 V03GD0000719 CHIP CERAMIC CAPACITOR (1608) C5010 V03GD0000719 CHIP CERAMIC CAPACITOR (1608) C5011 V03GD0000719 CHIP CERAMIC CAPACITOR (1608) C5012...
Page 182 U02A AV TERM (PE0195) Стр. 1 из 6 Loading ... Parts Location Description U02A 75004438 PWU, AV TERM, PE0195A1 C101 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K C102 76762471 CAPACITOR, ELECTROLYTIC, 10V 470UF M C103 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K C104 76766479 CAPACITOR, ELECTROLYTIC, 50V 4.7UF M C105...
Page 183 U02A AV TERM (PE0195) Стр. 2 из 6 C640 76073073 CAPACITOR, ELECTROLYTIC, 35V 2200UF M C641 76073073 CAPACITOR, ELECTROLYTIC, 35V 2200UF M C642 76092883 CAPACITOR, CERAMIC CHIP, 50V B 0.1UF K C645 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K C665 76092731 CAPACITOR, CERAMIC CHIP, 16V B 1UF K C666...
Page 184 U02A AV TERM (PE0195) Стр. 3 из 6 CC06 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K CC07 76109152 CAPACITOR, CERAMIC CHIP, 50V B 1500PF K CC08 76109152 CAPACITOR, CERAMIC CHIP, 50V B 1500PF K CC32 76105100 CAPACITOR, CERAMIC CHIP, 50V CH 10PF D CC90 76212103 CAPACITOR, CERAMIC DISC, 50V B 0.01UF K CC91...
Page 185 U02A AV TERM (PE0195) Стр. 4 из 6 CG39 76105560 CAPACITOR, CERAMIC CHIP, 50V CH 56PF J CG40 76105560 CAPACITOR, CERAMIC CHIP, 50V CH 56PF J CG41 76105560 CAPACITOR, CERAMIC CHIP, 50V CH 56PF J CG42 76105050 CAPACITOR, CERAMIC CHIP, 50V CH 5PF C CG43 76105010 CAPACITOR, CERAMIC CHIP, 50V CK 1PF C CG44...
Page 186 U02A AV TERM (PE0195) Стр. 5 из 6 CS31 76073086 CAPACITOR, ELECTROLYTIC, 50V 10UF M CS32 76092611 CAPACITOR, CERAMIC CHIP, 6.3V B 2.2UF K CS33 76092515 CAPACITOR, CERAMIC CHIP, 16V F 4.7UF Z CS34 76092731 CAPACITOR, CERAMIC CHIP, 16V B 1UF K CS35 76092611 CAPACITOR, CERAMIC CHIP, 6.3V B 2.2UF K CS50...
Page 187 U02A AV TERM (PE0195) Стр. 6 из 6 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.690\32W... 02.05.2015...
Page 188 U02B LED (PE0195) Стр. 1 из 1 U02B LED (PE0195) Location Parts No. Description U02B 75004439 PWU, LED, PE0195A2 CB02 76202221 CAPACITOR, ELECTROLYTIC, 10V 220UF M CB03 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z CB04 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z CB05 76202221 CAPACITOR, ELECTROLYTIC, 10V 220UF M...
Page 189 U02C KEY (PE0195) Стр. 1 из 1 U02C KEY (PE0195) Location Parts No. Description U02C 75004440 PWU, KEY, PE0195A3 DA01 23362042 DIODE, ZENER, UDZS6.8B DA06 23362042 DIODE, ZENER, UDZS6.8B DA07 23362042 DIODE, ZENER, UDZS6.8B PJ42B 23713948 CONNECTOR, S6B-PH-K-S(LF) RA71 76011683 RESISTOR, CHIP, 1/20W 68K OHM J RA72 76011223...
Page 190 U02D DB DOWNLOAD (PE0195) Стр. 1 из 1 U02D DB DOWNLOAD (PE0195) Location Parts No. Description U02D 75004441 PWU, DB DOWNLOAD, PE0195A4 CL02 76092883 CAPACITOR, CERAMIC CHIP, 50V B 0.1UF K GR60 76000445 CHIP JUMPER, 1608TYPE GR61 76000445 CHIP JUMPER, 1608TYPE PL05A 23713754 PLUG, 3P 2.5MM G, B3B-EH-F1-TV4...
Page 191 U03A FRONT HDMI (PE0196) Стр. 1 из 2 U03A FRONT HDMI (PE0196) Location Parts No. Description U03A 75004434 PWU, FRONT HDMI, PE0196A1 C604 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K C605 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K CC11 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K...
Page 192 U03A FRONT HDMI (PE0196) Стр. 2 из 2 R699 76871101 RESISTOR, CHIP, 1/8W 100 OHM J RC11 76011821 RESISTOR, CHIP, 1/20W 820 OHM J RC12 76011821 RESISTOR, CHIP, 1/20W 820 OHM J RH06 76011473 RESISTOR, CHIP, 1/20W 47K OHM J RH08 76011222 RESISTOR, CHIP, 1/20W 2.2K OHM J...
Page 193 U04A POWER (PE0197) Стр. 1 из 4 U04A POWER (PE0197) Location Parts No. Description U04A 75004473 PWU, POWER, PE0197A1 C801 76503507 CAPACITOR, PLASTIC FILM, AC275V 0.22UF K C802 76503507 CAPACITOR, PLASTIC FILM, AC275V 0.22UF K C803 76503169 CAPACITOR, PLASTIC FILM, 630V 0.1UF J C804 76214103 CAPACITOR, CERAMIC DISC, 500V B 0.01UF K...
Page 194 U04A POWER (PE0197) Стр. 2 из 4 CE43 76567104 CAPACITOR, PLASTIC FILM, 50V 0.1UF J CE82 76676470 CAPACITOR, ELECTROLYTIC, 100V 47UF M CE85 76073178 CAPACITOR, ELECTROLYTIC, 25V 3300UF M D801 23362200 DIODE, D5SB60, 7009F07 D801B 23717240 SCREW, BITTB3X10SZN D805 23357850 DIODE, ZENER, MTZJ9.1A D806 23357893...
Page 195 U04A POWER (PE0197) Стр. 3 из 4 L801 75004433 TRANSFORMER CHOKE 28MH 1.6A, ST-H0110 L802 23217794 TRANSFORMER, CHOKE, TPW2074AS L804 23103304 FERRITE CHOKE, TEM2011AA L805 23103304 FERRITE CHOKE, TEM2011AA L806 23248417 COIL, CHOKE, TLN3481AH L807 23248417 COIL, CHOKE, TLN3481AH L874 23103304 FERRITE CHOKE, TEM2011AA L875...
Page 196 U04A POWER (PE0197) Стр. 4 из 4 R817 76377224 RESISTOR, CARBON FILM, 1W 220K OHM J R821 76322689 RESISTOR, OXIDE METAL FILM, 1W 6.8 OHM J R827 76383103 RESISTOR, OXIDE METAL FILM, 2W 10K OHM J R828 76383103 RESISTOR, OXIDE METAL FILM, 2W 10K OHM J R853 76011103 RESISTOR, CHIP, 1/20W 10K OHM J...
Page 197 U04B LOWB (PE0197) Стр. 1 из 4 U04B LOWB (PE0197) Location Parts No. Description U04B 75004474 PWU, LOWB, PE0197A2 C851 76092538 CAPACITOR, CERAMIC CHIP, 10V F 1UF Z C852 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K C860 76668101 CAPACITOR, ELECTROLYTIC, 35V 100UF M CE35 76539334 CAPACITOR, PLASTIC FILM, 50V 0.33UF J...
Page 198 U04B LOWB (PE0197) Стр. 2 из 4 DE94 23357862 DIODE, ZENER, MTZJ11B DE96 23357867 DIODE, ZENER, MTZJ13A DE97 23357703 DIODE, 1SS355 DE98 23357842 DIODE, ZENER, MTZJ6.8B GE50 23103304 FERRITE CHOKE, TEM2011AA GE51 76000445 CHIP JUMPER, 1608TYPE LE52 23289049 COIL, PEAKING, TRF4330AU LE53 23248399 COIL, CHOKE, TLN3283D...
Page 199 U04B LOWB (PE0197) Стр. 3 из 4 QE94 23205292 TRANSISTOR, 2SD2396 QE95 23205330 TRANSISTOR, RN1403(F) QE96 75001876 TRANSISTOR, TPC8111(TE12L, Q) QE97 23205569 TRANSISTOR, 2SC2713-GR(TE85L, F QE98 23205568 TRANSISTOR, 2SA1163-GR(TE85L, F R850 76011101 RESISTOR, CHIP, 1/20W 100 OHM J R851 76011471 RESISTOR, CHIP, 1/20W 470 OHM J R852 76011471...
Page 200 U04B LOWB (PE0197) Стр. 4 из 4 RE74 76871122 RESISTOR, CHIP, 1/8W 1.2K OHM J RE82 76011473 RESISTOR, CHIP, 1/20W 47K OHM J RE83 76011473 RESISTOR, CHIP, 1/20W 47K OHM J RE88 76011222 RESISTOR, CHIP, 1/20W 2.2K OHM J RE91 76011103 RESISTOR, CHIP, 1/20W 10K OHM J RE92...

Toshiba 32WLT68 Service Manual

Quick Links

Related Manuals for Toshiba 32WLT68

Summary of Contents for Toshiba 32WLT68

Table of Contents