Vermont Castings WOODLAND VC1080PG1 Assembly And Operation Manual page 24

24
Grill produces excess or
discolored smoke
Grill will not achieve
or maintain stable
temperature
Er-1 Error code
Er-2 Error code
Er-P Error code
Er-L Error code
Er-H Error code
CONTACT US: 1-844-586-4660
Grease build-up Follow care and maintenance instructions.
Wood pellet quality Remove moist wood pellets from hopper. Follow care and maintenance
instructions to clean out. Replace with dry wood pellets.
Burn grate is blocked Clear burn grate of moist, wood pellets. Follow hopper priming procedure.
Insufficient air intake for fan Check fan. Ensure it is working properly and air intake is not blocked. Follow care
and maintenance instructions if dirty.
Control settings Check the LED screen to ensure that the act is enabled. If not short press the
prime button to shift the temperature display from set to act.
Insufficient air flow through Follow set-up procedure to ensure proper positioning of cooking components.
burn grate Check burn grate for proper positioning. Follow care and maintenance instructions
for ash build-up. Check that the air intake for the fan is not blocked. If no blockage,
remove hopper access panel (see electric wire diagram for diagram) and locate
the blue and white fan wires. Ensure that connection is tight by lightly tugging on
each wire. If loose, push back into connector until it clicks. Check fan blades for
cleanliness. Check grill probe. Follow care and maintenance instructions if dirty.
Check hopper for an obstruction in the feed system. Remove pellets and follow
care and maintenance instructions.
Lack of fuel, poor fuel Check hopper to check that fuel level is sufficient, and replenish if low. Should
quality, obstruction in feed the quality of wood pellets be poor, or the length of the pellets too long, this may
system cause an obstruction in the feed system. Remove pellets and follow care and
maintenance instructions.
Grill probe Check status of grill probe. Follow care and maintenance instructions if dirty.
Contact customer service for a replacement part if damaged.
The unit has overheated, Press the power button to turn the unit off and allow grill to cool. Follow care
possibly due to grease fire and maintenance instructions. After maintenance, remove pellets, and confirm
or excess fuel. positioning of all component parts. Once cooled, press the power button to turn
the unit on, then select desired temperature. If error code still displayed, contact
customer service.
Grill probe is not making a Check for damage to the grill probe. Follow care and maintenance instructions if
connection dirty. If all appears in working order, check the connection to the digital control
centre. Unplug unit from power source. Remove hopper access panel (see electric
wire diagram for diagram). Locate the white wires of the grill probe. Disconnect the
spade connectors, then reconnect until it clicks. Replace the hopper access panel.
Grills fails to perform start- Follow set-up procedure instructions. Check hopper for sufficient fuel or if
up cycle there is an obstruction in the feed system. Remove pellets and follow care and
maintenance instructions. Check grill probe. Confirm if actual temperature is
Grill will not stay lit
correct and accurate. Follow care and maintenance instructions if dirty. Check
igniter positioning and that it is heating up properly. In extreme cold, the grill may
require a second start. Turn grill off, wait, then turn on again. Check fan. Ensure it is
working properly. Follow care and maintenance instructions if dirty.
Temperature control dial Pressing the power on button replaces the error code with set temperature. If error
changed to any position code is still displayed, contact customer service.
other than off when
connected to power outlet
The unit is having low Press the power button/ turn the temperature control knob to off position
temperatures to switch off the unit off. Follow care and maintenance instructions. After
maintenance, remove the ashes and unburnt pellets from burn pot and bottom of
the grill and confirm positioning of all component parts. Press the power button
to turn the unit on, then select desired temperature. If error code is still displayed,
contact customer service.
The unit has overheated, Press the power button/ turn the temperature control knob to off position
possibly due to grease fire to switch off the unit off and allow grill to cool. Follow care and maintenance
or excess fuel. instructions. After maintenance, remove the ashes and unburnt pellets from
burn pot and bottom of the grill and confirm positioning of all component parts.
Once cooled, press the power button to turn the unit on, then select desired
temperature. If error code is still displayed, contact customer service.