Page 2
Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.) Samsung Electronics...
Page 3
Always inspect for pinched, out- of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. Samsung Electronics...
Page 4
2-10 Mechanical Parts (2) (Sub Chassis) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-20 Notice You can search for the updated part code through ITSELF web site. URL; http://itself.sec.samsung.co.kr Samsung Electronics...
Page 5
All manuals and user guides at all-guides.com Exploded View and Parts List 2-1 Ass’y Lens/Deck Samsung Electronics...
Page 6
All manuals and user guides at all-guides.com Exploded View and Parts List Loc. No Parts No. Description ; Specification Remark AD97-07502C ASSY-MAIN BOARD;-,VP-D30/XEU,THETA-PJ AD97-06882A ASSY-CHASSIS DECK;ASSY,THETA-PJ,- AD63-00487A SHIELD-CASE FPC;THETA-PJ,SPTE,T0.25,50,3 AD61-01287A BRACKET-LENS;THETA-PJ,SUS,T0.5,-,-,-,- AD97-06757A ASSY-FRONT BOARD;THETA-PJ,-,- AD97-04747A ASSY-LENS;-,DVC10X,SUML AD29-00019A FILTER-OPTICAL LPF;-,VP-D73,-,-,3.4X4.5X AD60-00053A SPACER-CCD;ALPHA_PJ,SILICON,-,-,-,BLK,-,...
Page 7
All manuals and user guides at all-guides.com Exploded View and Parts List 2-2 Ass’y EVF/CVF Samsung Electronics...
Page 21
All manuals and user guides at all-guides.com Exploded View and Parts List 2-9 Mechanical Parts (1) (Main Chassis) M401 M403 M416 M414 M415 M413 M412 M406 M405 M410 M408 M407 M404 M409 M411 M402 2-18 Samsung Electronics...
Page 23
All manuals and user guides at all-guides.com Exploded View and Parts List 2-10 Mechanical Parts (2) (Sub Chassis) S315 S310 S311 S306 S301 S312 S307 S308 S303 S309 S302 S313 S305 S304 S314 2-20 Samsung Electronics...
Page 25
All manuals and user guides at all-guides.com Exploded View and Parts List MEMO 2-22 Samsung Electronics...
Page 26
All manuals and user guides at all-guides.com 3. Electrical Parts List Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark AD97-07502C ASSY-MAIN BOARD;-,VP-D30/XEU,THETA-PJ C510 2203-000438 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1005,- C111 2203-005344 C-CERAMIC,CHIP;22nF,10%,25V,X7R,TP,1005, C511 2203-005061 C-CERAMIC,CHIP;100nF,+80-20%,16V,Y5V,TP, C112 2203-005344 C-CERAMIC,CHIP;22nF,10%,25V,X7R,TP,1005,...
Page 57
The Power Reset means that you pull out the power source and pull in it again. Fig. 1-2 - : - - : - - : - VCRADJ Indicates current adjustment item Indicates the adjusted values Indicates preset values Fig. 1-3 Samsung Electronics...
Page 58
SWP Position Head Switching Position Adjust 1) How to adjust Head Switching Position Œ Get into VCR ADJUST mode. ´ Move to the VCR ADJUST address “437”. ˇ Play standard tape, and “Head Switching Position” will be adjusted automatically. Samsung Electronics...
Page 59
´ Press the push the “MENU Selector” when storing confirmed adjustment value of each adjustment step in EEPROM. ˇ The OSD shows “OK” after finishing each adjustment step. ¨ To clear the adjustment mode, pull out the power source. Samsung Electronics...
Page 60
Ø After setting adjustment value, please push the CAM DISP “MENU Selector” to confirm Data. DSC ADJ STEP 3 LCD/CVF ADJ CAMERA EPR EVR Monitor OSD shows " ". Then camera adjustment mode has been activated successfully. Fig. 2-2 Samsung Electronics...
Page 61
ˆ Press the “EASY”(Mode Up)/”DISPLAY”(Mode Down) buttons so that OSD shows "ODE XX XX". Ø Press the “MENU Selector” (Confirm). Never impact on the lens when adjusting zoom and focus Lens. The OSD shows “OK” after finishing the adjustment. 3M ± 1cm (Be sure to maintain the distance) LENS Fig. 2-4 Samsung Electronics...
Page 62
¨ Ensure that camera picks up image 40 µs on 5100 gray scale chart (3100 gray scale chart + C16 filter) precisely and the illumination is 1500~2000 Lux. ˆ Press the “MENU Selector” (Confirm) to ensure that white spot on a vectorscope is moving in the middle of screen. Ø The OSD shows “OK” after finishing the adjustment. Samsung Electronics...
Page 63
DISPLAY (Mode Down) Shift adjustment address to right. MENU Selector up (Data Up) Up value. MENU Selector down (Data Down) Down value. Note : In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics...
Page 64
All manuals and user guides at all-guides.com Alignment and Adjustments 3-3 Adjust Mode <Table 3-2> SYSTEM NTSC Address 123K LCD 211K LCD 123K LCD 211K LCD Samsung Electronics...
Page 65
1) Set the power-supply output to approx.3V. <Table 4-1> 2) Choose the polarity (depending on whether load- Movement of chassis ing or unloading). Loading 3) Supply the voltage to the Motor Loading, and set to the desired mode. Unloading DC POWER SUPPLY Fig. 4-2 Samsung Electronics...
Page 66
Œ In EJECT mode, clean the tape path system(from Pole Tension P1 through Pole Review P7, Pinch Roller and Capstan Shaft) and the Lower Drum. Using the lens tissue soaked in ethyl alcohol. Note : Make sure that no oil or grease adheres to the lens tissue. PINCH ROLLER Fig. 4-3 Samsung Electronics...
Page 67
(Oil contaminated with dust might cause the bearings to wear out or seize.) ◆ A “drop”of oil is defined as the amount attached to the tip of a Ø 2mm stick as shown in Fig. 4-4. Fig. 4-4 Samsung Electronics...
Page 68
(If it is located outside, adjust toward arrow B.) Note : Check if the Arm Tension can be moved toward arrow C in PB mode. 3) Reassembly Œ For the removal of the Housing Ass’y. ± 1 0.3 ARM TENSION CAP ADJUSTMENT Fig. 4-5 Samsung Electronics...
Page 69
Œ For the removal of the Idler Ass’y. ´ For the removal of the Housing Ass’y. ± A, B : 3.9 0.1mm REEL DISK S TABLE REEL DISK T TABLE RESTING SURFACE RESTING SURFACE CHASSIS SUB Fig. 4-6 Samsung Electronics...
Page 70
¨ Check that the waveform of the RF signal is flatat both inlet and outlet(A in Fig. 4-7). If not flat (B or C in Fig. 4-7), do adjustments 4-5(b) through 4-5(d). INLET OUTLET NORMAL DEFECT AT INLET DEFACT AT OUTLET Fig. 4-7 S REEL T REEL Fig. 4-8 Samsung Electronics...
Page 71
´ Set to REV mode and observe the outlet waveform of PB RF signal. (Fig. 4-11) ˇ If the outlet waveform is out-of-spec, turn P7 counterclockwise, and redo steps 1 and 2. CAPSTAN P5 Fig. 4-11 Fig. 4-10 Samsung Electronics...
Page 72
If the track pitch is not uniform, do section 4-5(b) (Tracking adjustment) and 4-5(c) (P7 adjustment). ´ Set to CUE mode. Confirm that the waveform peaks still have a uniform pitch. (Fig. 4-14 B) If the track pitch is not uniform, do section 4-5(b) (Tracking Adjustment). Fig. 4-14 Samsung Electronics...
Page 73
Œ In CUE and REV modes, check that the tape is not curled around the P1, P3, P5 upper flange and P7 upper/Lower flanges. P7 CAPSTAN P5 Fig. 4-15 FROM THE S REEL FROM THE T REEL Fig. 4-16 Samsung Electronics...
Page 74
All manuals and user guides at all-guides.com Alignment and Adjustments MEMO 4-10 Samsung Electronics...