Advertisement
6
2600-VCO
Power Connection
The 2600-VCO module comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these
steps to connect the module to your Eurorack case.
1. Turn the power supply or rack case power off and disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will
align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient
pin 1 (-12 V) with the red stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for
correct orientation.
4. After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.
Installation
The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows
individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module,
but each plate should be positioned in the approximate relation to the mounting holes in your module before attaching the screws.
Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate. Attach
the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position
has been established, tighten the screws down.
Specifications
Inputs
Keyboard CV
Type
1 x 3.5 mm TS jack,
DC coupled
Impedance
100 kΩ, unbalanced
CV range
10 V, 1 V/oct.
FM1 / 2 / 3 CV
Type
3 x 3.5 mm TS jacks,
DC coupled
Impedance
50 kΩ, unbalanced
CV range
10 V, 1 V/octave
PWM CV
Type
1 x 3.5 mm TS jack,
DC coupled
Impedance
75 kΩ, unbalanced
CV range
10 V, typically 1 V/10%
Outputs
TRI/SINE/SAW/PULSE
Type
4 x 3.5 mm TS jacks,
DC coupled
Impedance
1 kΩ, unbalanced
TRI level
±5 V
SINE level
±5 V
SAW level
0 V / +10 V
PULSE level
0 V / +10 V
Hereby, Music Tribe declares that this product is in compliance with Directive
2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/
EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK - 8200 Aarhus N, Denmark
Quick Start Guide
Controls
Initial oscillator
Sets oscillator frequency
frequency fader
(10 oct. range)
Fine tune knob
Oscillator fine tune
adjustment (±0.4 oct.)
Audio (Kybd on) / LF
Select audio band
(Kybd off) slide switch
(10 Hz to 10 kHz) or
LFO (0.03 Hz to 30 Hz)
FM 1 / 2 /3 faders
Attenuate FM inputs
(-∞ to unity gain)
Pulse width fader
Pulse width adjustment
(10% to 90%)
PWM fader
Pulse width
modulation attenuator
(-∞ to unity gain)
Power
Power supply
Eurorack
Current draw
140 mA (+12 V),
5 mA (-12 V)
Physical
Dimensions (H x W x D)
129 x 81 x 42 mm
(5.08 x 3.19 x 1.65")
Rack units
16 HP
Weight
0.15 kg (0.33 lbs)
7
Advertisement
