Advertisement
Quick Links
Advertisement
Related Manuals for Daewoo L520B
Summary of Contents for Daewoo L520B
- Page 1 USER’S GUIDE TFT LCD-MONITOR Model No : L520B http://www.dwe.co.kr...
- Page 2 FEDERAL COMMUNICATIONS COMMISSION WICHTIGE INFORMATIONEN RADIO FREQUENCY INTERFERENCE STATEMENT Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät in Betrieb This equipment has been tested and found to comply with the limits NOTE : nehmen! Lesen Sie sich außerdem die Bedienungsanleitung komplett und for a Class B digital device, pursuant to Part 15 of the FCC Rules.
- Page 3 Seoul, Korea monitor and must be easily accessible. declare under our sole responsibility that the product, ® As an ENERGY STAR Partner, Daewoo Electronics Co., Ltd. has ® TFT LCD monitor determined that this product meets the Energy Star guidelines for L520B energy efficiency.
-
Page 4: Table Of Contents
CONTENTS INTRODUCTION CONTENTS INTRODUCTION Introduction ................1 This manual explains how to correctly install, operate and get the best performance from your monitor. Please read this user’s Product Features ..............2 guide carefully before installing your monitor, then keep it near your monitor for quick reference. -
Page 5: Product Features
SETUP SETUP PRODUCT FEATURES INSTALLING THE STAND The monitor is designed for use in a small work area or for Unfolding the stand those who need more work space on the desk. The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. -
Page 6: Connecting The 15 Pin Signal Cable And Power Cord
OPERA TION & ADJUSTMENT OPERA TION & ADJUSTMENT CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD CONTROL PANEL 1. Turn off the computer and monitor. POWER POWER Indicator shows both normal operation swithes the monitor on 2. Connect the 15 pin signal cable to the output port of the video and power management status and off. - Page 7 KEY PROCESS ADJUSTMENT PROCEDURE MENU Is the H.Size Adjust the control. CLOCK proper? 1024X768 UT L TY UT L TY MENU MENU Perform the AUTO Is the POSITION noise displayed on EXIT EXIT UT L TY SHARPNESS SHARPNESS the screen? EXIT Perform the AUTO...
- Page 8 OSD FUNCTIONS ICON CONTROL FUNCTION ICON CONTROL FUNCTION Select language for OSD (6 languages). LANGUAGE Adjust the display OSD Menu. TIME OUT Adjust the width (horizontal size) of the Display horizontal & vertical frequency CLOCK STATUS screen image. and polarity. Sharpen the focus by aligning the Reset the screen to the Factory Preset illuminated pixels and adjust until the...
- Page 9 SPECIFICA TIONS SPECIFICA TIONS SELF DIAGNOSIS Panel Size 15-inch (38 cm) diagonal Pixel Pitch 0.297 x 0.297 mm Viewing Angle 60°(Right/Left) If there is no image, the Self Diagnosis screen will be displayed. 40°(up), 60°(down) Self Diagnosis function checks if the status of the monitor screen Contrast Ratio 350:1 contrast ratio (typ) is “No Signal”, “Out of range”...
-
Page 10: Factory Preset Timings
ACTOR Y PRESET TIMINGS CHANGING THE ST ACTOR Y PRESET TIMINGS CHANGING THE ST REMOVING THE STAND VESA MODES Resolution Mode H.Freq (KHz) V.Freq (Hz) Remark (dots lines) 60Hz 31.5 Non-interlaced . Remove 2 screws. 72Hz 37.9 Non-interlaced . Remove the Stand Rear. 75Hz 37.5 Non-interlaced... - Page 11 TROBLESHOOTING TROBLESHOOTING REMOVING THE COVER Symptom Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. Remove the Cover. No picture. Check if power switch and computer power switch are in the on position. Check if the signal cable is correctly connected to the video card.
- Page 12 APPENDIX APPENDIX DESCRIPTION FOR D-SUB CONNECTOR Signal Green Blue GND-Red GND-Green GND-Blue +5Vdc GND-H.Sync GND-V.Sync Bi-directional Data(SDA) Horizontal Sync Vertical Sync(VCLK) Data Clock(SCL) GND=Ground S/N:9978632100...