Changing The Room Temperature; More Settings - Bosch HPC 400 Operating Instructions Manual

Getting started
~
Press the menu key to open the main menu.
~ Press the selector to open the HeatingfCooling menu.
~
Press the selector to open the Operating mode menu.
I
~~
If two or more heating circuits are installed. turn the selector to highlight Heating
circuit
1. 2. 3
or
4
and press the selector.
Turn the selector to highlight Optimise and press the selector.
I
~
Press and hold the Back key to return to the standard display.
I
The required room temperature is shown in a pop:up window in the lower part of the
display. The user interface will now constantly maintain the required room
temperature.
Table 5 Getting started - Activating operating modes
4.3 Changing the room temperature
Fr, 21 ,03.201.
Lto.SOC
Flow temperature
He1 Optimise
BOSCH
12:35
10
12.5' C
6720812n~ . 10
Operating the appliance Result
If it is too cold or too warm for you today:
a..n.. .... .-........... , . _
Changing the room temperature until the next switching time
~
Turn the selector to set the required room temperature.
The corresponding time slot is displayed in grey in the time program bar chart.
~ Wait a few seconds or press the selector.
The user interface operates with the modified setting. The change applies until
the next switching time in your heating system time program is reached . After
i
this. the time program settings are restored.
I
E
I
Undoing a temperature change
i
~
Turn the selector until the corresponding time slot turns back to black in the time
o program bar chart and press the selector.
~
The change is undone.
Fr,21.03.20'4
12:35
Lto.SOC
10
12.5'c
~ow temperature
He3 Pro •. ,
·0 0
C!l 1ll':"
6 720 812 n5-()S.10
Should it be permanently
too
cold
or
too hot for you: ................
II., .... ___
~~
___
---!
~
Activate optimised operation
(~
Chapter 4.2) .
~ Wait a few seconds or press the selector to close the pop·up window.
~ Turn the selector to set the required room temperature.
~
Wait a few seconds or press the selector. Press the selector to confirm the change
in the pop·up window (or press the back key to discard the change) .
Table 6
The room temperature that is currently valid is shown in a pop·up window in the
lower part of the display.
The user interface operates with the modified settings.
Getting started - Room temperature
Fr, 21.03 201.
HCC(Heltlnr clreutt 4)
Chana' room temp.
ror
optimised
heat pump optratlon to lO.O·C7
12:35
6720 812 n5-OO.10
10 HPC400-6720821983(2017/07)
BOSCH
Getting started
Operating the appliance Result
~
Press the menu key to open the main menu.
~
Press the selector to open the HeatingfCooling menu.
~
Turn the selector to highlight the Temperature settings menu.
I
~
Press the selector to open the menu.
~
If two or more heating circuits are installed. turn the selector to highlight Heating
circuit 1. 2. 3 or 4 and press the selector.
~I
I
~
Turn the selector to highlight Heating. Setback or Cooling.
-----f
... Press the selector.
~
Turn the selector and press it to activate the required setting. e.g. for setlback
mode. .
~
Turn and press the selector to set the temperature. The limits ofthe setting values
I
1
for the temperatures are determined by the settings forlhe other operating mode
·in each case.
1
The user interface operates with tlhe modified settings. The settings are applied
~
to all time programs for the heating system (if two or more heating circuits are
c
installed. it is only applied in the selected heating circuit).
Table 6 Getting started - Room temperature
4.4 More settings
m
II til
Ir
1111 I
I
Heating 21.0'C
Setback
I
15.0'C
Cooling
I
19.0'C
6720 811 136-07.10
o
Heitlngoff
, • • 'C 50 - = 20.5
Ent.rthe setback temperature
6 720 811 1:MHl8. 10
Operating the appliance Result
If you need hot water
outside of the times set
If!
the time program: AcIIRIt-. .... (. immecrllte DHW function).
~ Press the extra DHW key.
DHW heating is active immediately with the set temperature and for the set duration.
After a few seconds. the symbol for extra DHW will be displayed in the information
graphic (Extra hot water settings
~
Chapter 5.3.3. page 22).
To deactivate the extra DHW function before the end of the set duration:
~ Press the extra DHW key again.
If the DHW is
too
cold
or
too
hot for you:
a-.. ........................
~ Press the DHW key.
The user interface will display a list of the DHW heating operating modes (for more
information ~ Chapter
5.3.1.
page
21).
~ Turn the selector to highlight the required operating mode.
I
~ Press the selector.
The user interface operates with the modified settings. Your contractor can set the
temperatures for the DHW and DHW reduced operating modes.
If optimised mode is active. the temperature will not be changed.
Table
7
Getting started - More settings
Fr,21.D3.2D1.
Lto.SOC
Flow temperatUf1
He1 OPtlml,.
12~35
10
12.5"
6720812nlHl9.10
o
~Iways
on • OHW red.
I
o Always on . DHW
Ir l·~~~n~tl~me~p~ro~w~~------~I
S,~ct operatlnr mode ror
DHWsystem.
6720811 136-10.10
HPC 400 - 6720821983 (2017/07) 11