Download Print this page

Installation - Koolatron KBC88-W Instruction Manual

Kool compact fridge
Hide thumbs Also See for KBC88-W:

Advertisement

INSTALLATION

1. Unpack your refrigerator by removing all packaging materials like carton, base, foams, adhesive tape, etc.
2. Remove all accessories, internal packaging material used to hold shelves, ice tray, etc. in place.
3. Clean the remains of all adhesive tap used and remove all printed material supplied.
4. Install the refrigerator in a convenient location away from extreme heat and cold. Allow sufficient clearance
between the refrigerator and side wall so the door(s) will open without obstruction. Refrigerator is not
designed for recessed installation.
5. The floor on which the refrigerator should be placed must be flat, hard, solid, and even. The refrigerator
should not be placed on any soft material such as foam, plastic, etc.
6. To level your refrigerator, use the two leveling legs located on the bottom front of your refrigerator. Adjust
by turning the legs counter clockwise to raise or clockwise to lower your refrigerator. The door will close
easier if the leveling legs are extended.
7. The following are recommended minimum clearances around the refrigerator for proper air circulation:
- Sides: 3/4" (19mm)
- Top: 2" (50mm)
- Back: 2" (50mm)
PROPER AIR CIRCULATION WILL HELP YOUR REFRIGERATOR WORK AT MAXIMUM EFFICIENCY.
NOTE - The appliance must be correctly connected to the power supply.
CAUTION - Care should be taken during the handling moving and use of the freezer to avoid damaging the
refrigerant tubing or increasing the risk of a leak.
WARNING - It is important to keep the power cord away from the compressor at the back of the refrig-erator
as during operation, the compressor can reach a high temperature and could cause serious damage to the
power cord.
PROTECTION FROM HEAT AND MOISTURE
• Do not install your refrigerator in any location where heavy moisture is present or if the location is not
properly insulated. This refrigerator is not designed to operate in temperature setting below 55°F.
• Location for the refrigerator should be on a hard surface and away from direct sunlight and heat source,
e.g., radiators, baseboard heaters, cooking appliances, etc.
DOOR ALIGNMENT
1. Remove the top hinge cover.
2. Loosen the top hinge screws using a Phillips head screwdriver.
3. Adjust the door or put a spacer in between and then tighten the screws.
STARTING YOUR NEW REFRIGERATOR
After cleaning your refrigerator thoroughly. Wipe the outside with a soft
dry cloth, the interior with a clean moist cloth.
1. Insert the power supply cord into the socket.
2. Turn the thermostat dial to an initial setting of "7" for 15-20 minutes.
NOTE - As the door gets pressed in during shipping, the gasket may have to be reset. This is done to prevent
the cool refrigerated air from escaping. If there is a gap between the door gasket and the cabinet, set the
gasket by gently pulling it out of the seal gap.
Door Hinge Cap
4
INSTALLATION (cont.)
REVERSING THE DOOR HINGE
1. Remove the top hinge cover.
2. Using Phillips Head Screwdriver, loosen and remove the screws holding the top hinge in place.
3. Remove top hinge and carefully lift off the door.
4. Remove the screw hole plugs from the opposite side and insert the plugs in the screw hole openings of
the just removed screws.
5. Remove any loose items in the refrigerator and carefully turn refrigerator on its back and place in a secure
area.
6. Loosen the screws holding the lower hinge bracket to the refrigerator and remove screws and bracket.
7. Remove the screws from the other side and insert in the previously removed screw holes.
8. Remove door pin by turning counter clockwise and reinsert to the underside of the bracket and tighten.
9. Align bracket and insert (2) remaining screws into the holes provided .
10. Align hole in the door with the door pin and washer and gently push down until firm.
11. Align upper hinge bracket with screw holes insert screws and partially secure, check that door and
cabinet are properly aligned and then secure tightly.
12. Replace hinge cap.
5

Advertisement

loading