Advertisement
FEATURES
Your Shark Steam Mop utilises steam to remove tough grease, dirt and grime. Steam is
nature's purest and most powerful cleaner for safely cleaning all hard floor surfaces in
your home without harsh chemicals, thus being perfectly ecological. Cleans your tile,
hardwood, linoleum and vinyl floors.
1. Quick & Easy
Eliminates rinsing, wringing, carrying buckets of water and redistributing the dirt on
the floor.
2. Powerful
Powerful steam dries quickly unlike traditional mopping. Uses powerful steam for
superior cleaning and sanitising.
3. No Harsh Chemicals
Use plain tap water or distilled water. Leaves no chemical residue behind.
4. Lightweight
No heavy buckets to carry. The Shark Steam Mop weighs only 1.85 kgs.
Only one third the weight of carrying a bucket of water and a mop.
5. Ergonomic Soft Grip Handle
Comfortable design makes it easy to manoeuvre without physical strain.
6. Quick Start-Up
Steam is ready in just 30 seconds.
7. Power "On" Light
The power "On" light will turn green when the unit is plugged in.
8. Reusable Cleaning pad
Durable triple layer microfibre cleaning pad loosens, lifts and locks in dirt. Just
toss in the washing machine when done.
4
OPERATING INSTRUCTIONS
How To Assemble Your Steam Mop
1. Remove all the parts from the
packaging.
2. Insert the upper extension
tube into the lower
extension tube. (Fig. 1)
Push it in until you
hear it click into place.
3. Insert the extension
tube assembly
into the pump
actuator. Make
sure that the
locking tab snaps
into place.
Pump
(Fig. 1)
actuator
4. Place the microfibre
cleaning pad
underneath the
mop head. Make
sure that the hook
and latch strips are
Fig. 1
facing up. (Fig. 2)
Press to secure.
TIP:
The microfibre
cleaning pads have
a coloured tab so that
a different pad can
be assigned to
different tasks or
rooms in the
Hook & latch
house.
strips
Fig. 2
Filling the Water Tank
IMPORTANT:
Always insure that the
unit is "UNPLUGGED" from the wall
receptacle prior to initial filling and before
attaching the microfibre cleaning pad to
the bottom of the mop head. Never use
the steam mop without
the microfibre cleaning
pad attached to the
mop head.
1. Turn the cap
MAX
counter clockwise
and then lift up to
remove from the
water tank. (Fig. 3)
Fig. 3
2. Using the filling flask and funnel, pour
one flask of water into the water tank.
Do not overfill the unit passed the
"MAX" fill line on the water tank.
(Fig. 3)
3. Replace the cap onto the water tank.
Using the Steam Mop
IMPORTANT: Never use the steam mop
without the microfibre cleaning pad
attached to the mop head or without water
in the water tank.
Please note that when using for the first
time, the appliance may take longer than
the normal 30 second startup time to
steam. You may need to pump the handle
a few times before the steam is released.
This is due to the water making its way
from the water tank through the pump and
into the heater. This will only occur during
the first use.
1. Sweep or vacuum floors before using
the steam mop.
2. Twist the quick release cord holder to
unwrap the power cord completely.
3. Plug into a 240V electrical outlet.
4. The power "On" light will turn green.
5. It takes approximately 30 seconds for
Mop
head
the unit to heat up and the steam to be
ready.
6. Pump the handle a few times to
dampen the microfibre cleaning pad.
Begin mopping with a forward and
backward motion, this pumping action
will release steam as you mop.
7. When the water tank is empty, the
steam mop will stop emitting steam.
Unplug the power cord from the
electrical outlet and refill the water tank
following the instructions above.
8. When you have finished using the
steam mop, unplug the unit from the
electrical outlet and carefully remove
the microfibre cleaning pad from the
mop head. Please note that the
microfibre cleaning pad gets very hot
with the steam. Always use caution
when removing.
9. Never leave the microfibre cleaning
pad on the steam mop head when
you have finished using the steam
mop.
5
Advertisement
