Advertisement
TX Power Output
1. Tune the frequency to 440.050 MHz, then set the trans-
mit power level to "LOW."
2. Press the [ F/W ] key, then press the [ BAND ( BAND DN )]
key to set the alignment parameter to "A2 PWR.xxx
3. With in five second of appearing the "A2 PWR.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the wattmeter read-
ing is 0.5 Watts (±0.05 Watt).
4. Increase the Transmit power level to "MID."
5. Press the [ F/W ] key to recall the alignment parameter
A2 PWR.xxx."
A2 PWR.xxx
A2 PWR.xxx
"A2 PWR.xxx
A2 PWR.xxx
6. With in five second of appearing the "A2 PWR.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the wattmeter read-
ing is 2.0 Watts (±0.1 Watt).
7. Increase the Transmit power level to "HIGH."
8. Press the [ F/W ] key to recall the alignment parameter
A2 PWR.xxx
A2 PWR.xxx
"A2 PWR.xxx
A2 PWR.xxx."
A2 PWR.xxx
9. With in five second of appearing the "A2 PWR.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the wattmeter read-
ing is 5.0 Watts (±0.1 Watt).
10. Tune the frequency to 146.050 MHz, then set the trans-
mit power level to "LOW."
11. Press the [ F/W ] key to recal the alignment parameter
A2 PWR.xxx
A2 PWR.xxx
"A2 PWR.xxx
A2 PWR.xxx."
A2 PWR.xxx
12. With in five second of appearing the "A2 PWR.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the wattmeter read-
ing is 0.5 Watts (±0.05 Watt).
13. Increase the Transmit power level to "MID."
14. Press the [ F/W ] key to recall the alignment parameter
"A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx."
A2 PWR.xxx
15. With in five second of appearing the "A2 PWR.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the wattmeter read-
ing is 2.0 Watts (±0.1 Watt).
16. Increase the Transmit power level to "HIGH."
17. Press the [ F/W ] key to recall the alignment parameter
"A2 PWR.xxx
A2 PWR.xxx" again.
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx
18. With in five second of appearing the "A2 PWR.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the wattmeter read-
ing is 5.0 Watts (±0.1 Watt).
FT-60R/E Technical Supplement
TX Deviation
1. Tune the frequency to 440.050 MHz, then set the trans-
2. Inject a 1 kHz audio tone at a level of 80 mV (–20 dBm)
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx."
A2 PWR.xxx
A2 PWR.xxx" on
A2 PWR.xxx
3. Press the [ F/W ] key, then press the [ BAND ( BAND DN )]
A2 PWR.xxx
4. With in five second of appearing the "A3 DEV.xxx
A2 PWR.xxx" on
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx
5. Tune the frequency to 146.050 MHz, then set the trans-
6. Press the [ F/W ] key to recall the alignment parameter
7. With in five second of appearing the "A3 DEV.xxx
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx" on
A2 PWR.xxx
DCS TX Deviation
1. Tune the frequency to 440.050 MHz, then activate the
2. Press the [ F/W ] key, then press the [ BAND ( BAND DN )]
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx" on
3. With in five second of appearing the "A4 DCS.xxx
4. Tune the frequency to 146.050 MHz, then activate the
A2 PWR.xxx
A2 PWR.xxx" on
A2 PWR.xxx
A2 PWR.xxx
5. Press the [ F/W ] key to recall the alignment parameter
6. With in five second of appearing the "A4 DCS.xxx
A2 PWR.xxx
A2 PWR.xxx
A2 PWR.xxx" on
A2 PWR.xxx
mit power level to "LOW."
from the audio generator.
key to set the alignment parameter to "A3 DEV.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the deviation meter
reading is 4.2 kHz (±0.2 kHz) (EXP version: 4.5 kHz ±
0.2 kHz).
mit power level to "LOW."
A3 DEV.xxx
A3 DEV.xxx."
A3 DEV.xxx
to "A3 DEV.xxx
A3 DEV.xxx
the display, press the PTT switch to activate the trans-
mitter, adjust the DIAL knob so that the deviation meter
reading is 4.2 kHz (±0.2 kHz) (EXP version: 4.5 kHz ±
0.2 kHz).
DCS, and set the transmit power level to "LOW."
key to set the alignment parameter to "A4 DCS.xxx
the display, press the PTT switch to activate the trans-
mitter (with no microphone input), adjust the DIAL
knob so that the deviation meter reading is 0.7 kHz
(±0.05 kHz).
DCS, and set the transmit power level to "LOW."
to "A4 DCS.xxx
A4 DCS.xxx."
A4 DCS.xxx
A4 DCS.xxx
A4 DCS.xxx
the display, press the PTT switch to activate the trans-
mitter (with no microphone input), adjust the DIAL
knob so that the deviation meter reading is 0.7 kHz
(±0.05 kHz).
Alignment
A3 DEV.xxx
A3 DEV.xxx."
A3 DEV.xxx
A3 DEV.xxx
A3 DEV.xxx
A3 DEV.xxx" on
A3 DEV.xxx
A3 DEV.xxx
A3 DEV.xxx
A3 DEV.xxx" on
A3 DEV.xxx
A3 DEV.xxx
A4 DCS.xxx
A4 DCS.xxx
A4 DCS.xxx."
A4 DCS.xxx
A4 DCS.xxx
A4 DCS.xxx
A4 DCS.xxx
A4 DCS.xxx" on
A4 DCS.xxx
A4 DCS.xxx
A4 DCS.xxx
A4 DCS.xxx" on
11
Advertisement
