Magnavox 55MV314X Owner's Manual page 36

Select this setting if your router has a Wi-Fi
Protected Setup (WPS) button. Start scanning
for wireless networks on the TV after pressing
Simple Connect
the WPS button on your router. If connection
test fails, try Simple Connect again.
refer to the router's manual for more details.
Select this setting if your router has a WPS but
does not have a WPS button. Enter the 8-digit
WPS code
WPS PIN code shown on your TV in the router
settings menu via PC before Connect is selected.
If your wireless network with authentication
setting (WEP
WPA / WPA2 Key entry screen will appear. Enter
Manual
the WEP
*2
wireless network using H I J K, then press
OK.
*1 WPS (Simple Connect) cannot be used when the security protocol
is set to WEP. Change the Access Point's security mode from WEP
to WPA or WPA2 (recommended).
*2 WEP is not recommended to be used due to its Major security
flaws. Change the Security protocol on the wireless router to WPA
or WPA2 (recommended) mode.
Confirmation message will appear. Select OK to complete the settings.
Note(s)
For a wireless network with authentication setting, key icon appears to the right hand of
●
the SSID.
Signal icon shows the strength of the signal.
●
WEP / WPA key appears as asterisks on the confirmation screen.
● *2
The wireless LAN supports following specifications.
●
Wireless standards: IEEE 802.11 b/g/n
–
Frequency spectrum: 2.4GHz
–
Security protocol: WEP / WPA / WPA2
–
*2
Manually enter your SSID
Set up the connection to the AP (e.g. wireless router) manually by entering
the SSID.
4
Use H I to select Manually enter your SSID, then press OK.
AP (e.g. wireless router) SSID entry screen will appear.
●
Enter the SSID using H I J K, then select OK.
5
Use H I to select the authentication setting of the selected wireless
network.
For a wireless network with authentication setting, select the
●
authentication setting, according to the security type of the
wireless network.
Auto XXXXXXXXXXXXXX
Manually enter your SSID
None Set the authentication setting to None.
WEP
Set the authentication setting to WEP
WPA/WPA2
Set the authentication setting to WPA/WPA2
For a wireless network without authentication setting, select None.
●
If it fails then
*1
, WPA or WPA2), WEP /
*2 *2
/ WPA / WPA2 key of the selected
None
WEP
WPA/WPA2
.
*
If you select WEP or WPA/WPA2, WEP
● *
screen will appear. Enter the WEP
wireless network using H I J K, then press OK.
Confirmation message will appear. Select Yes to complete the settings.
●
* WEP is not recommended to be used due to its Major security flaws.
Change the Security protocol on the wireless router to WPA or WPA2
(recommended) mode.
IP configuration
In following cases, select IP configuration to set each setting as necessary.
When connection test failed with the setting of Connection test.
–
When instructed by your Internet service provider to make specific
–
settings in accordance with your network environment.
3
Use H I to select IP configuration, then press OK.
4
Use H I to select a setting, then press OK.
Network selection IP setting mode
Wireless network setting IP address
IP configuration
Subnet mask
Proxy configuration Default gateway
Primary DNS
Secondary DNS
MAC address
Auto
Sets the IP setting automatically.
IP setting
mode
Manual
Sets the IP setting manually.
A set of numbers which are assigned to
IP address
devices participating in a computer
*1, 3
network.
A mask which is used to determine what
Subnet mask
*1, 3
subnet an IP address belongs to.
IP address of the network device (such as
Default gateway
*1, 3
router) which provides Internet access.
DNS Auto
Sets the DNS setting automatically.
setting
Manual
Sets the DNS setting manually.
mode
A server which handles the name and IP
Primary DNS
*2, 3
address over the Internet.
A server which handles the name and IP
Secondary DNS
*2, 3
address over the Internet.
An address which recognizes the devices
MAC address
connecting to the network. It is also called
Hardware Address.
*1 Items can be selected only when IP setting mode is set to
Manual.
*2 Items can be selected only when DNS setting mode is set to
Manual.
*3 Use H I or the NUMBER buttons to input numbers. When you
use H I to input numbers, then press OK or input the triple digits
by using the NUMBER buttons, the cursor moves to the next entry
field. When you use H I to input numbers, then press OK or input
the triple digits by using the NUMBER buttons at the rightmost
entry field, numbers will be stored and go back to the previous
menu.
36
/ WPA / WPA2 Key entry
*
/ WPA / WPA2 key of the selected
*
Manual
192.168.11.3
255.255.255.0
192.168.11.1
192.168.11.1
0.0.0.0
00:12:0E:10:09:15
Continued on next page.
.
English