Table of Contents
Advertisement
Quick Links
SERVICE
MICROWAVE OVEN
SEA
MICROWAVE OVEN
BASIC : SMH7175WC
MODEL : SMH7175BE
SMH7175WE
Manual
1. Precaution
2. Specifications
3. Operating Instructions
4. Disassembly and Reassembly
5. Alignment and Adjustments
6. Troubleshooting
7. Exploded Views and Parts List
8. PCB Diagrams
9. Schematic Diagrams
10. Reference
CONTENTS
SAM0117
Advertisement
Table of Contents
Related Manuals for Samsung SMH7175WC
Summary of Contents for Samsung SMH7175WC
- Page 1 MICROWAVE OVEN BASIC : SMH7175WC MODEL : SMH7175BE SMH7175WE SERVICE Manual MICROWAVE OVEN CONTENTS 1. Precaution 2. Specifications 3. Operating Instructions 4. Disassembly and Reassembly 5. Alignment and Adjustments 6. Troubleshooting 7. Exploded Views and Parts List 8. PCB Diagrams 9.
-
Page 2: Table Of Contents
Contents 1. Precaution 1-1 Safety precautions ................1 1-2 Special Servicing Precautions (Continued) . - Page 3 Contents 7-2 Main Parts List ................26 7-2 Main Parts List .
- Page 4 PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not operate or allow the oven to be (c) Before turning on microwave power for operated with the door open. any service test or inspection within the (b) Make the following safety checks on all microwave generating compartments, ovens to be serviced before activating the...
-
Page 5: Precaution
1. Precaution Follow these special safety precautions. Although the microwave oven is completely safe during ordinary use, repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as potentially lethal high voltages and currents. 1-1 Safety precautions ( 1. -
Page 6: Special Servicing Precautions (Continued)
1-2 Special Servicing Precautions (Continued) 17. When checking the continuity of the witches or transformer, always make sure that the power is OFF, and one of the lead wires is disconnected. 18. Components that are critical for safety are indicated in the circuit diagram by shading, 19. -
Page 7: Specifications
2. Specifications 2-1 Table of Specifications TIMER 99 MINUTES 99 SECONDS POWER SOURCE 120V 60Hz POWER CONSUMPTION MICROWAVE : 1,650W OUTPUT POWER FROM 100 TO 1100W(10 LEVEL POWER) (IEC-705 TEST PROCEDURE) OPERATING FREQUENCY 2,450MHz MAGNETRON OM75PH(31)ESS COOLING METHOD COOLING FAN MOTOR OUTSIDE DIMENSIONS ”(W) x 15 ”(H) x 15... -
Page 8: Operating Instructions
3. Operating Instructions 3-1 Control Panel Sens or Reheat Pow er/Aut o Defrost Sets weight of food to be defrosted. Sens or Cook Buttons Sensor settings to cook popular foods. Handy Help er, Kid s Meals, Snack Bar Selects type of dish to be reheated. More/Less Increase or decrease cooking time. -
Page 9: Features & External Views
3-2 Features & External Views Door Ventilation Holes Oven Light Safety Interlock Holes Control Panel Handle Intake Holes Glass Tray Guide Roller Door Latches 758.9mm 398mm - 5 -... -
Page 10: Accessary
3-3 Accessary shelf Glass tray Roller guide ring Shelf Registration card Top template Installation Instructions Owner’s menual Wall template Hardware-kit Grease filters Charcoal filter exhaust adaptor - 6 -... - Page 11 3-4 INSTALLATION The Microwave Oven is supported by a special bracket assembly (mounting system) supplied with the oven. The bracket assembly must be mounted to the wall with toggle bolts through the wall, and a lag screw into a wall stud. After the bracket assembly is installed, the unit can be slid over the two rails of the bracket assembly.
- Page 12 3-5 REUSABLE GREASE FILTERS The metal filter trap grease released by foods on the cooktop. They also prevent flames from foods on the cooktop from damaging the inside of the microwave. For this reason, the filters must ALWAYS be in place when the hood the vent fan is used.
-
Page 13: Disassembly And Reassembly
4. Disassembly and Reassembly MAGNETRON, MOTOR ASSEMBLY, VENT BLOWER AND HIGH VOLTAGE TRANSFORMER Oven must be removed from wall. REMOVING OVEN FROM WALL (2 PEOPLE REQUIRED) Oven is hooked on metal tabs at bottom of wall mounting plate and to cabinet by (3) top cabinet bolts. 4-1 Replacement of High Voltage Transformer and Fan Motor Assembly. -
Page 14: Replacement Of Door Assembly
4-3 Replacement of Door Assembly 4-3-1 Removal of Door Assembly Remove hex bolts securing the upper hinge and lower hinge. Then remove the door assembly. Door "A" Door "C" 4-3-2 Removal of Door “E” Following the procedure as shown in the figure, insert and bend a thin metal plate between Door “E”... -
Page 15: Reassembly Test
4-3-4 Reassembly Test After replacement of the defective component parts of the door, reassemble it and follow the instruc- tions below for proper installation and adjustment so as to prevent an excessive microwave leakage. 1. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the oven face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment. -
Page 16: Replacement Of Stirrer Motor
4-6 Replacement of stirrer motor 1. Disconnect power and remove grille screws(2). 2. Remove grille and the bracket duct upper screw(1). 3. Remove the bracket duct upper and disconnect the stirrer motor wire. 4. Remove stirrer motor screws(1) and lift up stirrer motor after turn left. -
Page 17: Replacement Of Control Circuit Board
4-8 Replacement of Control Circuit Board 4-8-1 Removal of Control Box 1. Disconnect power and remove grille. 2. Be sure to ground any static electric charge in your body and never touch the control circuit. 3. Disconnect the connectors from the control circuit board. -
Page 18: Alignment And Adjustments
5. Alignment and Adjustments PRECAUTION 1. High voltage is present at the high voltage terminals during any cook cycle. 2. It is neither necessary nor advisable to attempt measurement of the high voltage. 3. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the high voltage capacitor. -
Page 19: High Voltage Capacitor
5-4 High Voltage Capacitor 1. Check continuity of the capacitor with the meter set at the highest resistance scale. 2. Once the capacitor is charged, a normal capacitor shows continuity for a short time, and then indicates 9MΩ. 3. A shorted capacitor will show continuous continuity. 4. -
Page 20: Vent Exhaust Blower Motor
5-8 VENT EXHAUST BLOWER MOTOR THIS COMPONENT REQUIRE REMOVAL OF MICROWAVE OVEN FROM INSTALLATION FOR SERVICING. The blower is a two speed (HI-LO) capacitor run blower assembly located on top of the micro- wave oven. The blower is operated by low voltage relays located on the smart board. -
Page 21: Thermal Cutout(Tco's)
5-9 THERMAL CUTOUT(TCO’S) There are 4 different thermal cutouts in this unit with 4 different purposes. They are : 1. Oven thermal cutout (flame sensor), on cavity top. 2. Hood thermal cutout, inside control area on duct. 3. Bottom thermal cutout, on floor of control area. 4. -
Page 22: Hood Thermal Cutout
5-9-3 Bottom Thermal Cutout This cutout will protect the touch control from exces- sive heat by turning the vent fan on at low speed. If the HOOD THERMAL CUTOUT surface units of the range are used for long periods of time heat will build up and could damage the micro- wave control. -
Page 23: Magnetron Thermal Cutout
5-9-5 Magnetron Thermal Cutout The magnetron thermal cutout is located above the leads to the magnetrons. It is designed to prevent MAGNETRON THERMAL CUTOUT damage to the magnetron if an overheated condition develops in the tube to cooling fan failure, obstructed air ducts, dirty or blocked air intake. -
Page 24: Output Power Of Magnetron
5-11 Output Power of Magnetron CAUTION MICROWAVE RADIATION PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE GENERA- TOR OR OTHER PARTS CONDUCTING MICROWAVE ENERGY. The output power of the magnetron can be measured by performing a water temperature rise test. Equipment needed : * Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm) * One glass thermometer with mercury column... -
Page 25: Procedure For Measurement Of Microwave Energy Leakage
; Samsung Electronics America, Inc. Headquarters 105 Challenger Road Ridge field Pack, New Jersey 07660-0511 5-15-2 At least once a year have the microwave energy survey meter checked for accuracy by its manufacturer. -
Page 26: Troubleshooting
6. Troubleshooting PRECAUTION 1. CHECK GROUNDING BEFORE CHECKING FOR TROUBLE. 2. BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT. 3. DISCHARGE THE HIGH VOLTAGE CAPACITOR. 4. WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT ONE LEAD WIRE FROM THESE PARTS AND THEN CHECK CONTINUITY WITHOUT THE POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE READING OR DAMAGE TO YOUR METER. -
Page 27: Electrical Malfunction(Continued)
6-1 Electrical Malfunction(continued) SYMPTOM CAUSE CORRECTIONS Oven lamp and fan motor turn 1. Misadjustment or loose wiring Adjust door and latch switches. of primary latch switch 2. Defective primary latch switch Oven can program but timer 1. Open or loose wiring of secondary i Adjust door and interlock switches. -
Page 28: Exploded Views And Parts List
7. Exploded Views and Parts List 7-1 Exploded Views P090 P125 M060 P088 P007 P087 U008 P125 P089 P091 P006 P012 M061 T017 P013 P014 T001 P032 P097 M015 T032 M219 C089 M068 P034 P039 P124 M024 M001 M036 P015 P122 P030 M049... -
Page 29: Main Parts List
7-2 Main Parts List (S.N.A : SERVICE NOT AVAILABLE) Level Code No. Description Specification Q’ty SA/SNA Remark M036 4713-001013 LAMP-INCANDESCENT 130V,-,40W,ORG,E17/20, DUCT UPPER M038 DE26-00082D TRANS H.V SHV-U1870B,120V,60HZ,2460/2220 M024 DE31-00029B MOTOR VENTILATION SMV-460UA-1,SMH7175WE/ M049 DE31-10172A MOTOR-SYNCHRONOUS M2HJ24Z709,ST-16F,21V, M050 DE31-10173A MOTOR-SYNCHRONOUS M2HJ29A709,ST-16F,21V, M029 DE47-20007A... -
Page 30: Main Parts List
SMH7175,MOUNTING+WIR P125 DE66-00121A WIRE-MOUNTING SMH7175,MSWR10,ZNC2,-,- P007 DE70-00378A PLATE-MOUNTING SMH7175,SECC ,-,T0.8,W130 M021 DE97-00365C ASSY-COVER MOTOR SMH7175/SMH7178,ASSY-NO M023 DE31-10177E MOTOR FAN SMF-1850UA1,SMH7175WC,-,60HZ,- H018 DE31-90051A BLADE-FAN P.P,T,D130,-,-,-,- P109 DE63-00141A COVER-MOTOR SMH7175,PP(FB53),T2.5,-,-,-, M017 DE96-00400B ASSY NOISE FILTER SN-UF12B,250V20A,OTR10 P034 DE97-00366C ASSY-DUCT UPPER SMH7175,HUMIDITY SENSOR,... -
Page 31: Control & Door Parts List
DE64-00864A DOOR-SUB SMH7175,PP,T1.5,-,-,-,BLK,- D024 DE64-00910A SCREEN-DOOR(B) SMH7175,TEMP-GLASS,T3.2,W D004 DE94-00882B ASSY DOOR-E(COATING) SMH7175BC,BLK-COATI D020 DE97-00358A ASSY-HANDLE SMH7175,BLK,-,- (BE) D020 DE97-00358B ASSY-HANDLE SMH7175WC,WHT,-,- (WE) D026 DE63-00139A COVER-HANDLE SMH7175,PC,T2.0,BLK,-,-,-,- (BE) D026 DE63-00139B COVER-HANDLE SMH7175,PC,T2.0,WHT,-,-,-,- (WE) D019 DE64-00761A HANDLE-DOOR SMH7175,PC,T2.0,-,-,-,BLK,- (BE) D019 DE64-00761B HANDLE-DOOR SMH7175,PC,T2.0,WHT,-,-,-,-... -
Page 32: Standard Parts List
7-4 Standard Parts List (S.N.A : SERVICE NOT AVAILABLE) Level Code No. Description Specification Q’ty SA/SNA Remark DE60-20066A BOLT-FLAT UNF1/4,L110,MSWR10,-,-,OTR6,-, DE60-20022A BOLT-TOGGLE MSWR,W3/16X75,-,-,-,-,-,-,- DE60-30015A NUT-FLANGE M5,P0.8,MSWR10,FEFZY,-,-,-,-,- DE60-30063A NUT-MOUNTING -,M6.3,S10C,ZNC,YEL,-,-,-,- DE60-30022A NUT-TOGGLE SBC1,ZPC2,WHT,-,-,-,-,-,- DE60-10082I SCREW-A -,-,-,-,2S-4X12,FEFZY,-,-,-,- BASE-P & CVT BACK DE60-10082I SCREW-A -,-,-,-,2S-4X12,FEFZY,-,-,-,- BKT DUCT REAR... -
Page 33: Diagrams
8. P.C.B Diagrams 8-1 P.C.B Diagrams ( This Document can not be used without Samsung’s authorization ) - 29 -... -
Page 34: Parts List
8-2 P.C.B Parts List (S.N.A : SERVICE NOT AVAILABLE) LEVEL Code No. Description Specification Q’ty SA/SNA Remark 0204-001118 FLUX SV-95-1F,C19H29COOH,C3H7OH,-,1 1.33 2011-000777 R-NETWORK 47Kohm,5%,1/8W,A,SIP,8P,TP AR01 3501-000256 RELAY-POWER 110V,1200VA,10000MA,-,10MS,1 RY04 3501-001155 RELAY-MINIATURE 24VDC,200MW,3000MA,1FORM RY11 3708-001550 CONNECTOR-FPC/FC/PIC 16P,1.25mm,STRAIGHT CN01 3711-000879 CONNECTOR-HEADER BOX,3P,1R,2.5mm,STRAIGH CN05 3711-000999 CONNECTOR-HEADER... -
Page 35: Parts List(Continued)
8-2 P.C.B Parts List(continued) (S.N.A : SERVICE NOT AVAILABLE) LEVEL Code No. Description Specification Q’ty SA/SNA Remark DE41-00309A PCB-MAIN RAS-OTR7HV,FR-1,1,-,T1.6,197*19 1203-001037 IC-VOLTAGE REGULATOR 78L05,SOT-89,3P,185 IC05 2401-002216 C-AL 2200uF,20%,35V,GP,TP,16x25,7.5 DE13-20009A KA7533,DIP,-,-,-,-,- IC03 2004-005092 R-METAL 348KOHM,1%,1/8W,AA,TP,1.8X3.2MM 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM 2004-004255 R-METAL 3.32KOHM,1%,1/8W,AA,TP,1.68X3.81 2004-000517 R-METAL 200KOHM,1%,1/8W,AA,TP,1.8X3.2M... -
Page 36: Schematic Diagrams
9. Schematic Diagrams 9-1 Schematic Diagrams ( This Document can not be used without Samsung’s authorization ) - 32 -... -
Page 37: Reference
10. Reference 10-1 Model name standard Baoad Distin- Middle Distin- Product Full Nane Classification guisher Classfication guisher Code USA CMO CMO (Counter- USA CMO(EPOXY CAVITY) top MWO) UTC (Under The USA UTC Cabinet) Browner, Grill USA GRILL Convection USA CONVECTION Sensor USA CMO SENSOR DC MWO... -
Page 38: Customer Inquiry Cases And Countermeasures
• Close the door completely. => Press the Cancel but- ton. => Press the Start button. • Contact the nearest Samsung after-sales service cen- ter. Ground • Ground problem may • If the oven is placed in a humid area, buy an electric happen when the oven wire in a store selling electrical products. - Page 39 Accessory • Visit the nearest Samsung Service Center or local dealer to buy accessories. Before visiting, check the model name printed on the lower right side of the front panel of the oven.
- Page 40 © Samsung Electronics Co., Ltd. July 2005 This Service Manual is a property of Samsung Electronics Co.,Ltd. Printed in Korea Any unauthorized use of Manual can be punished under applicable Code No. : DE68- 03964A International and/or domestic law.