Tires - Cub Cadet 20HP Z-Force 48 Operator's And Service Manual

ing brake switch must be repositioned or
perhaps replaced. If the engine does not
start, engage the parking brake and start
the engine. Swing one steering lever up to
the operating position and the engine
should stop. If the engine does not stop,
the parking brake switch must be reposi-
tioned or replaced.
c. Left and Right Steering Lever Switches:
Sit in the operator's seat. With both steer-
ing levers opened-out in the neutral posi-
tion, the parking brake engaged and the
blade clutch switch "off", swing the left
steering lever up to the operating position
and try to start the engine. The engine
should not start. If it does, the left steering
lever switch must be repositioned or per-
haps replaced. Open the left steering lever
to the neutral position and swing the right
steering lever up to the operating position
and try to start the engine. The engine
should not start. If it does, the right steer-
ing lever switch must be repositioned or
perhaps replaced. If the engine does not
start, open the right steering lever to the
neutral position and start the engine.
Swing the left steering lever up to the oper-
ating position and the engine should stop.
If the engine does not stop, the left steering
lever switch must be repositioned or
replaced. Open the left steering lever out
to the neutral position and start the engine.
Swing the right steering lever up to the
operating position and the engine should
stop. If the engine does not stop, the right
steering lever switch must be repositioned
or replaced.
d. Seat Switch: With both steering levers
opened-out to the neutral position, the
parking brake engaged and the blade
clutch switch in the "off" position, start the
engine. Now release the parking brake,
hold down on the back of the operator's
seat against spring pressure, and swing
one of the steering levers up to the operat-
ing position. Release the operator's seat
and the engine should stop. If the engine
does not stop, the seat switch must be
replaced. With both steering levers folded
out in the neutral position, the parking
brake engaged and the blade clutch switch
in the "off" position, sit in the operator's
seat and start the engine. Turn the blade
clutch switch to the "on" position and the
blades should start to rotate. Raise up
slightly off the operator's seat and the
blades should stop. If the blades do not
stop when you dismount from the opera-
tor's seat, the seat switch must be
replaced.
e. Electric PTO Clutch: This clutch operates
when the engine is running, the operator is
in the operator's seat and the blade clutch
switch is turned on. This electric clutch is a
fairly trouble free device. If a problem
develops and the blades do not turn, first
check the 20 amp fuse in the yellow, 16-
gauge wire between terminal "L" on the
ignition switch and the hour meter and then
investigate the wiring harness and the con-
nections to the seat switch, the blade
clutch switch and the electric blade clutch.
Then check the seat switch, the blade
clutch switch and finally the electric blade
clutch.
f. No Cut in Reverse Switches: When both
speed/direction levers are moved past
"neutral" to reverse, the PTO Clutch will be
deactivated and the mower blades will stop
rotation. The PTO will be reactivated when
one or both of the levers are moved back to
"Neutral".
D.Tires
The two front wheels are caster wheels that are free
to swivel to accommodate the direction of the mower.
The two rear wheels are used to propel the mower in
the direction of input from the drive handles. Inflation
pressure of the rear tires is important for stability
while the mower is in operation. If the tire diameter is
not equal between the two tires, the mower will pull to
one side.
1. Inflation Pressure:
a. Traction Tires—20 psi max; 8-10 psi rec-
ommended
b. Front Caster Wheel—28 psi max; 20-25
psi recommended
c. Cutting Deck Ball Wheels—Solid Polyure-
thane.
Use the Following guidelines for maintaining the tires:
a. Balance inflation pressure between the
rear tires to help maintain straight travel
(see tire side wall for proper inflation pres-
sure).
b. Keep the valve caps tightened to prevent
air pressure loss.
2. Leaking Tires: When a flat tire occurs, repair
or replace immediately. The normal procedure
is to remove the wheel and replace it. If a tire
is getting soft, park the mower on the nearest
level, paved area. If the leaking tire is on a
traction wheel, put blocks on each side of the
opposite traction wheel and jack up the tire
20