Specifications, descriptions, and illustrative material herein are as accurate as known at time of publication but are subject to change without notice. In case of questions, refer to your NEW HOLLAND Sales and Service Networks. 48126536 05/04/2017...
INTRODUCTION Safety rules Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions.
INTRODUCTION Safety rules General safety rules Use caution when operating the machine on slopes. Raised equipment, full tanks and other loads will change the center of gravity of the machine. The machine can tip or roll over when near ditches and embankments or uneven surfaces.
Page 13
INTRODUCTION Operate controls only when seated in the operator’s seat, except for those controls expressly intended for use from other locations. Before leaving the machine: 1. Park machine on a firm level surface. 2. Put all controls in neutral or park lock position. 3.
Page 14
INTRODUCTION When welding, follow this instructions in the manual. Always disconnect the battery before welding on the machine. Always wash your hands after handling battery components. Wheels and tires Make sure tires are correctly inflated. Do not exceed recommended load or pressure. Follow instructions in the manual for proper tire inflation.
Page 15
INTRODUCTION Do not weld or flame cut any items that contain flammable material. Clean items thoroughly with non-flammable solvents before welding or flame-cutting. Do not expose the machine to flames, burning brush, or explosives. Promptly investigate any unusual smells or odors that may occur during operation of the machine. General battery safety Always wear eye protection when working with batteries.
Page 16
INTRODUCTION If the system is inoperable, the system must be repaired. Power Take-Off (PTO) PTO-driven machinery can cause death or serious injury. Before working on or near the PTO shaft or servicing or clearing the driven machine, put the PTO switch in the disengage position, stop the engine, and remove the key. Whenever a PTO is in operation, all guards must be in place to prevent death or injury to the operator or bystanders.
Page 17
INTRODUCTION • Clean belts only with soap solution and warm water. • Do not use bleach or dye on the belts because this can make the belts weak. To fasten the belt, pull it from the reel and push the tongue end (3) into the buckle end (2) until a "click" indicates it is fully engaged.
Page 18
INTRODUCTION Keep out of reach or children or other unauthorized persons. Additional precautions are required for applied chemicals. Obtain complete information from the manufacturer or distributor of the chemicals before using them. Utility safety Make sure the machine has sufficient clearance to pass in all directions. Pay special attention to overhead power lines and hanging obstacles.
Page 19
INTRODUCTION Never mount or dismount from a moving machine. Do not use the steering wheel or other controls or accessories as handholds when entering or exiting the cab or operator’s platform. Header lift locks Do not work under the machine header unless it is securely blocked and/or the header safety latch is engaged. Header will fall rapidly if hydraulic lift system should fail.
Improper disposal of batteries can contaminate the soil, groundwater, and waterways. NEW HOLLAND strongly recommends that you return all used batteries to a NEW HOLLAND dealer, who will dispose of the used batteries or recycle the used batteries properly. In some countries, this is a legal requirement.
INTRODUCTION Safety signs The following safety signs are on your machine as a guide for your safety and for the safety of those working with you. Walk around the machine and note the content and the location of all safety signs before you operate your machine. Keep all safety signs clean and legible.
Page 24
INTRODUCTION IMPORTANT WHEN BACKING UP, HOLD THE STEERING WHEEL AT BACK OF RIM AND MOVE YOUR HAND IN THE DIRECTION YOU WANT TO GO Quantity 1 86555355_F 86555355_F (1) Attached to steering wheel. NHIL14WR00277AA WARNING INSTRUCTIONAL SEAT To be used for training or diagnostic purposes. Extra riders, especially children, are NOT permitted on machine.
Page 25
INTRODUCTION WARNING Before starting engine or any function. Warn bystanders. Sound horn 3 times. Failure to comply could result in death or serious injury. Quantity 1 84012892_E 84012892_E (3) On the right-hand side cab glass, upper side of glass. NHIL14WR00268AA EMERGENCY EXIT If it becomes impossible to open the cab door, while in the cab, the right cab window can be used as...
Page 26
INTRODUCTION WARNING SLIPPERY SURFACE DO NOT use this area as a step or platform. Failure to comply could result in death or serious injury. Quantity 1 87026533_B 87026533_B (5) Top engine hood, front. NHIL14WR00271AA DANGER DO NOT use ether starting fluid with a "THERMOSTART"...
Page 27
INTRODUCTION WARNING PRESSURIZED FLUID DO NOT remove radiator cap. CHECK coolant level in recovery tank. Failure to comply could result in death or serious injury.. Quantity 1 329045A1 329045A1 (7) Rear side of top engine hood. NHIL15WR00471AA WARNING TO PREVENT LOSS OF CONTROL DO NOT tow on public roads or use recovery hook point as a hitch.
Page 28
INTRODUCTION CAUTION CRUSHING HAZARD Keep hands and fingers away from moving parts under screen. Failure to comply may result in injury. Quantity 1 47690158 47690158_A (9) Left-hand lower side of the rotary air screen vanity plate. NHIL14WR00276AA 48126536 05/04/2017...
Page 29
INTRODUCTION WARNING ROTATING PARTS Keep hands and clothing away from rotating fan and belts. Failure to comply could result in death or serious injury. Quantity 2 332511A1 332511A1 (10) Left-hand side of fan shroud. NHIL14WR00280AA (10) Right-hand side of fan shroud. NHIL16WR00241AA 48126536 05/04/2017...
Page 30
INTRODUCTION WARNING Before operating machine, read operator's manual and ALL SAFETY instructions. If manual is missing, contact your dealer or service department. Before starting engine or operation, clear area of bystanders. Keep all shields in place, keep hands, feet, clothing and hair away from moving parts.
Page 31
INTRODUCTION DANGER NEVER allow riders on this machine. Failure to comply will result in death or serious injury. Quantity 1 84004732 84004732_C (12) Rear side of the left-hand platform support. NHIL14WR00272AA WARNING Shut off the engine and remove the ignition key before performing maintenance or repair work.
Page 32
INTRODUCTION DANGER CRUSHING HAZARD - HEADER Header will fall rapidly if hydraulic lift system should fail. Rest header on ground or engage header lock handle before working around raised header. Failure to comply will result in death or serious injury. Quantity 2 84554251 84554251_B...
Page 33
INTRODUCTION WARNING TO PREVENT LOSS OF CONTROL The windrower must be properly ballasted as described in the Chapter 9 of the Operator’s manual. Review ballast requirements whenever changing headers. Failure to comply could result in death or serious injury. Quantity 1 47605933 47605933_A (15) Left front side of the main frame.
Page 34
INTRODUCTION WARNING PRESSURIZED FLUID OR GAS Hydraulic accumulator contains gas and oil under pressure. Service or repair must be performed only by trained service technician. Failure to comply could result in death or serious injury. Quantity 1 84005363 84005363_B Non draper units only (16) Left front side of the main frame.
Page 35
INTRODUCTION WARNING PRESSURIZED FLUID Use controller’s BLEED program to relieve system pressure before disassembling any hydraulic connection. Refer to service manual for more details. Failure to comply could result in death or serious injury. Quantity 1 47564945 47564945_A (17) Right-hand side frame rail near right-hand side platform.
Over-torquing of a hydraulic connection can also lead to leakage or failure. For some connections, NEW HOLLAND requires a different torque value than is listed in the ISO and SAE standards. • The torque values in this document should be used whenever possible or applicable.
Only use CNH Original Parts or NEW HOLLAND Original Parts. Only genuine spare parts guarantee the same quality, duration, and safety as original parts, as they are the same parts that are assembled during standard production. Only CNH Original Parts or NEW HOLLAND Original Parts can offer this guarantee.
Page 48
W0111A Special tools The special tools that NEW HOLLAND suggests and illustrate in this manual have been specifically researched and designed for use with NEW HOLLAND machines. The special tools are essential for reliable repair operations. The special tools are accurately built and rigorously tested to offer efficient and long-lasting operation.
INTRODUCTION Hydraulic contamination Contamination in the hydraulic system is a major cause of the malfunction of hydraulic components. Contamination is any foreign material in the hydraulic oil. Contamination can enter the hydraulic system in several ways: • When you drain the oil or disconnect any line •...