Table of Contents
Advertisement
Quick Links
S
afe Operation Practices Set-Up Operation Maintenance Service Troubleshooting
O
M
PERATOR'S
ANUAL
Hedge Trimmer CC927LH
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
FORM NO. 769-12355 02
DATE：01/25/2018
Advertisement
Table of Contents
Related Manuals for Cub Cadet CC927LH
Summary of Contents for Cub Cadet CC927LH
- Page 1 Operation Practices Set-Up Operation Maintenance Service Troubleshooting PERATOR’S ANUAL Hedge Trimmer CC927LH WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
-
Page 2: Table Of Contents
Thank You Please be aware that this Operator’s Manual may cover Thank you for purchasing a Hedge Trimmer manufactured a range of product specifications for various models. by MTD Asia. It was carefully engineered to provide Characteristics and features discussed and/or illustrated excellent performance when properly operated and in this manual may not be applicable to all models. -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS WARNING THIS HEDGE TRIMMER CAN CAUSE SERIOUS INJURIES. Read the instructions carefully for the correct handling, preparation, maintenance, starting and stopping of the hedge trimmer. become familiar with all controls and the proper use of the hedge trimmer. Clothing and Equipment Always wear proper eye glasses to prevent eyes from the risk of thrown objects. - Page 4 Before operation Before operating the hedge trimmer, always ensure that the operating position is safe and secure. Do not operate the hedge trimmer with a damaged or excessively worn blade. Always ensure that all handles and guards are fitted when using the hedge trimmer. Never attempt to use an incomplete hedge trimmer or one fitted with an unauthorized modication.
-
Page 5: Warning Labels And Symbols
WARNING LABELS AND SYMBOLS Read warning labels on the unit and understand them. If any label is missing, damaged, or worn get a replacement from your dealer and install it in the correct position. CHOKE SETTINGS SAFETY AND WARNING SYMBOL 1.CHOKE CLOSE starting position Indicates danger,warning or a reason 2.CHOKE OPEN running position... -
Page 6: Get To Know Your Hedge Trimmer
GET TO KNOW YOUR HEDGE TRIMMER LONG REACH HEDGE TRIMMER 1.Air Filter Cover 9.Throttle Trigger 2.Fuel Tank 10.Tube 3.Spark Plug Cap 11.Gear Case 4.Muffler Cover 12.Assist Handle 5.Throttle Cable 13.Blade Protect Teeth 6.Throttle Lockout 14.Blade 7.Ignition Switch 15.Loop Handle Assy 8.Grip... -
Page 7: Fuel And Oil Instructions
FUEL AND OIL INSTRUCTIONS WARNING 1. Only use high quality special oil for air cooled 2-stroke engine,JASO FC or FD, or ISO-L-EGC or EGD oil. Never use water cooled engine oil or any oil for 4-stroke engine. Fuel 1. Always use fresh, clean lead-free fuel. Minimum octane number: 90#. Mixing Ratio 1. -
Page 8: Assembly Instructions
ASSEMBLY INSTRUCTIONS INSTALL AND ADJUST HANDLE 1.Push the handle down onto the tube,and set the lower handle into the right place,so that the parts matched right. 2.Insert the bolt into the bolt hole and push it through.and put the nut into the nut hole on the lower handle back.tighten the bolt,but do not tighten the bolt completely. -
Page 9: Operating Instructions
OPERATING INSTRUCTIONS STARTING 6. When the engine is already warm or on hot days, set the choke lever to the position. Close WARNING Fully Open Before starting the engine, keep the cutting attachment clear of everything around it. Choke Lever WARNING Exhaust gases contain carbon monoxide, and colorless, odorless,poisonous gas. - Page 10 OPERATING 2.After starting the engine, run the engine at the idling speed for a few minutes. 3.The engine should be run at idle speed for a 1.When cutting the hedges ,the unit should be few minutes to allow sufficient warm-up time held so that the blades form 0-15°...
-
Page 11: Maintenace And Repair
MAINTENANCE AND REPAIR CARBURETOR 1. Idling speed can be adjusted by idle screw. 2. Adjusting the idle-speed screw clockwise will increase the idling speed and adjusting it counterclockwise will decrease the idling speed. You should use a tachometer to measure the speed while adjusting. Make sure the idling speed within the Fuel Filter recommended range 2700~3300 rpm. - Page 12 9. If spark plug is damaged or the unit still cannot work well after cleaning, replace with a Washing new one. 10. To ensure the machine work well Please use Drying the specified plug. Engine Oil Squeezing 0.6-0.7MM WARNING MUFFLER Improper element cleaning can result in Spark Arrester Service engine damage.Do not use compressed air...
- Page 13 oil inlet oil inlet BlADES 1. Please replace the blades if damaged or worn seriously. 2. Please use the sharpener or file to grind the cutting edges, referring to the angle in the below picture. 3. Clean the blades after grinding and apply the grease on the edges.
-
Page 14: Cleaning And Storage
CLEANING AND STORAGE CLEANING 1.Brush off dust and grass cuttings from the unit and wipe up water and oil stain with dry cloth. STORAGE 1. Keep the unit away from flames or sparks when it contains fuel. 2. Allow the unit to cool before storage. 3. -
Page 15: Trouble-Shooting
TROUBLE-SHOOTING Problem Cause Remedy 1. Reconnect wire. 1. Spark plug wire disconnected. 2. Set switch to ON. 2. Ignition switch set to OFF. 3. Add fuel. 3. Fuel tank empty. 4. Empty the tank and fill with fresh fuel 4. Stale or improperly mixed fuel mixture. -
Page 16: Specification
SPECIFICATION Model CC927LH Engine Mitsubishi MHI Air Cooled 2-Stroke Engine Carburetor Diaphragm Clutch Type Centrifugal Starter Recoil Displacement 25.6cc Max Power 0.8KW Mixing Ratio(Gasoline/OIl): 50:1 Idle Speed 3000+/-300 rpm Speed at Max,Torque: 6000 rpm Speed at Max,Power: 7500 rpm Gear Box Reduction Ratio: 4.8 Fuel Tank Capacity: 0.6L...