Mobilehub™Link Operation (Optional); About Mobilehub™ Link; Telephone Mode On/Off; Incoming Calls - Alpine CDA-9827 Owner's Manual

MobileHub™ Link Operation ( Optional )
SOURCE/ BAND/
8
-/J
POWER TEL.
g
f
9
F/SETUP
SEARCH
About MobileHub™ Link
Connect a separately sold Junction Box and a portable
telephone (available from Nokia) to control the incoming
and outgoing calls of the portable telephone.
CAUTION
• Even with hands-free operation, a driver can be distracted
during telephone operation or receiving a call. For the sake of
safety, drivers are requested to refrain from operating the
telephone while driving.
• For the sake of safety, operations other than incoming calls
and Speed-Dial outgoing calls cannot be used.
NOTES
• If a portable telephone is connected, its address book,
incoming and outgoing history are downloaded to the
Junction Box.
• Please refer to the instruction manual of the Junction BOX.

Telephone Mode ON/OFF

1
Press and hold the BAND/TEL. button for at least 2
seconds to turn ON Telephone mode.
To turn OFF, press the BAND/TEL. button.
See relevant pages for each item.
NOTES
• When a portable telephone is not connected, press and hold
the BAND/TEL. button for at least 2 seconds. "NO PHONE"
is displayed for about 2 seconds, then the mode returns to the
original source mode
• When the portable telephone is taken off the Junction BOX
during an incoming or outgoing call, or during a hands-free
call, the call will be treated as an ordinary one by the
portable telephone.
• When there is an incoming call while the power of CDA-9827/
CDA-9826/CDA-9825 is OFF, the power of CDA-9827/CDA-
9826/CDA-9825 will turn ON automatically for a hands-free
call.
• Even if the power of the portable telephone is OFF, when
CDA-9827/CDA-9826/CDA-9825 is set to the telephone
mode, the power of the portable telephone will be turned ON.
• Even if the ACC power of the vehicle is turned OFF (even if
the engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone
is possible.
• If there is an incoming call during operation (except an
outgoing call or talking), operation mode will end and switch
to the incoming or talking mode.
24
-EN
Rotary encoder
Preset buttons
(1 through 6)
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same
time from a portable telephone and CDA-9827/CDA-9826/
CDA-9825 as malfunction can result.
• With a Junction BOX connected outgoing, incoming, and
sending history will also be recorded in the portable
telephone.
• While telephoning, DEFEAT is also set to ON. When the call
has finished, the unit returns to the setting which you
previously set.
• The telephone volume can be adjusted from the CDA-9827/
CDA-9826/CDA-9825. The volume you set during the call is
memorized, and is automatically applied again on the next
call.
• While telephoning or receiving incoming calls, press the
DISP/TITLE button to indicate the Network Operator
display for 5 seconds.

Incoming Calls

1
Press the :/J button to receive an incoming call.
2
Press the BAND/TEL. button to finish a call.
The telephone mode will end and return to the original
source mode.
NOTES
•
When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call.
• The incoming call can be switched to Automatic Calling or
Manual Calling.
1. Press and hold the F/SETUP button for at least 3 seconds.
2. Select the TEL mode by pressing the g or f button.
3. Press the BAND/TEL. button to change to TEL AUTO or
TEL MANU.
4. Press the F/SETUP button to return to normal mode.
• Press the BAND/TEL. button during an incoming call to
disconnect it.