Samsung 5 Series Quick Setup Manual

Quick Setup Guide
Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
STOP
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
Please do not return this unit.
85 Challenger Road Ridgefield Park, NJ 07660-2112
If you have problems operating your
Samsung Electronics Canada Inc.
TV, call:
1-800-SAMSUNG (1-800-726-7864)
55 Standish Court Mississauga, Ontario L5R 4B2
For web support please visit:
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
www.samsung.com/support
To register this product, visit : www.samsung.com/register.
Getting Started
Step 1 :
Install the Stand
Follow the steps below to connect the TV to the stand.
Make sure to distinguish between the front and back of the Stand and Guide
✎
Stand when assembling them.
Make sure that at least two people lift and move the LCD TV.
✎
Lay the product down, with the screen facing up and fasten the screws.
✎
1
2
Screw
Stand
Step 2 :
Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1. Lift the cover on the back of the remote upward
as shown in the figure to the right.
2. Install two AAA batteries.
Make sure to match the + and - ends of
✎
the batteries to the diagram in the battery
compartment.
Replace the cover.
3.
Step 3 :
Connect Power and Antenna or Cable
Power Input
Use a 75 ohm (round) cable.
All manuals and user guides at all-guides.com
Connect AnT In to:
• Wall cable jack or
or
• VHF/UHF
Antenna or
• Cable or Satellite
box Ant or Cable
Out
Make sure the AC power cord
is plugged in securely to the
wall outlet and the TV.
Step 4 :
Connect External Devices
Connecting an AV device (Blu-ray player, cable/sate
For the very best picture quality, select HD signal sources and use HDMI cables and
connections. Note that many digital cable programs are not in HD. Check with your vi
provider to ensure your are receiving HD signals.
Step 5 :
Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process. It also
displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the
To skip a screen, press the MEnU
To turn on your TV, press the POwEr
POwEr button on the TV. To run Plug & Play, follow these steps:
Select Language of the OSD.
Language
1. On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press
Home Use screen appears.
2. Select Home Use, and then press
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press EnTErE button, the Antenna Source screen appears.
3. If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
press EnTErE button on your remote. The Select Cable System screen
appears.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
AV IN 2
Audio/Video connection (480i only)
Using an Audio/Video Cable
VCR
VIDEO OUT AUDIO OUT
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Lowest Quality Connection
EnTErE
button.
button on the remote or press the
Plug & Play
English
Español
: English
Français
U Move E Enter
EnTErE button. The
EnTErE button. If you select Store
button.