Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
INTRODUCTION Machine Description Manual Accuracy The Model T31681 1 HP Commercial-Grade Bone We are proud to provide a high-quality owner’s Saw is a stainless-steel and aluminum-alloy saw manual with your new machine! for cutting fresh or frozen meat and bones.
Support Rod Knob Fence Meat Support Rod Pusher Adjustable Fence On/Off Switch Fence Lock Knob Motor Enclosure Adjustable Foot Scrap Tray To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model T31681 (Mfd. Since 12/19)
C. Fence: Supports workpiece when making straight cuts. Distance from blade determines width of cut. Removable for cleaning and sanitizing. Figure 2. Rear components. Figure 1. Front components. Model T31681 (Mfd. Since 12/19)
Switch Type .............................. ON/OFF Push Button Motor: Main Horsepower ................................1 HP Phase ................................Single-Phase Amps ..................................8.5A Speed ................................1650 RPM Type ...................................ODP PSC Power Transfer ................................ Direct Bearings ........................Shielded & Permanently Lubricated Model T31681 (Mfd. Since 12/19) Model T31681 Page 1 of 2...
Page 8
Approximate Assembly & Setup Time..........................30 Min. Serial Number Location ..............................ID Label ISO 9001 Factory .................................. Yes Features: Adjustable Fence Scrap Meat Tray Non-Slip Rubber Feet Built-In Meat Pusher Model T31681 (Mfd. Since 12/19) Page 2 of 2 Model T31681...
Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model T31681 (Mfd. Since 12/19)
Page 10
Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model T31681 (Mfd. Since 12/19)
This machine is NOT designed to cut wood, own. DO NOT try to stop or slow blade with your metal, glass, stone, tile, etc. hand or the workpiece. Model T31681 (Mfd. Since 12/19)
Page 13
Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. -11- Model T31681 (Mfd. Since 12/19)
IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely Wear safety glasses during helpful if you need to return your machine later.
Figure 6. Minimum working clearances. Children and visitors may be seriously injured if unsuper- vised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use. -13- Model T31681 (Mfd. Since 12/19)
DISCONNECT MACHINE FROM POWER! Open wheel cover to expose wheels. Figure 9. Correct blade teeth orientation. Verify blade is centered in blade guide and rests against blade wipers, as shown in Figures 7 & 8. -14- Model T31681 (Mfd. Since 12/19)
CLEANING & SANITIZING on Page Blade Deflection 20 before beginning operation. Get in the habit of properly cleaning and sanitizing the saw before and after each use to avoid contamination and illness. Figure 11. Blade deflection during tensioning. -15- Model T31681 (Mfd. Since 12/19)
SECTION 4: OPERATIONS Changing Blade To reduce your risk of serious injury, read this The saw blade included with the Model T31681 is entire manual BEFORE a general purpose 4 TPI (Teeth Per Inch) blade. using machine. Under normal conditions, the saw blade should be replaced after sawing 4400 lbs.
Page 19
Rotate blade tension knob until blade no lon- ger moves freely. Verify blade teeth are facing down through table, as shown in Figure 14. Blade Teeth Facing Down Table Figure 14. Correct blade teeth orientation. -17- Model T31681 (Mfd. Since 12/19)
To prevent blade falling off wheels and causing injury or property damage, DO NOT rotate blade tensioning knob when saw is operating. Always disconnect machine from power before adjusting blade tension. Figure 16. Blade deflection during tensioning. -18- Model T31681 (Mfd. Since 12/19)
To complete a typical operation, the operator does the following: Makes sure all components of saw are The Model T31681 1 HP Commercial-Grade Bone properly cleaned and sanitized (refer to Saw is designed for cutting fresh or frozen meat CLEANING & SANITIZING on Page 20).
Figure 17. Upper wheel removed from shaft. food processing equipment and always fol- low the manufacturer's recommendations. To prevent illness or death, never use a product that will make the meat unsafe for human consumption. -20- Model T31681 (Mfd. Since 12/19)
Page 23
18. Re-assemble components and cover machine the highest possible heat settings. If it is an with a clean, dry cloth until next use. option, use the dishwasher to dry parts with hot air. -21- Model T31681 (Mfd. Since 12/19)
The best method for choosing a chemical sanitizer is to do the research and determine which product is best for your particular situation. Sanitizing solutions should be changed as soon as they become dirty, or every two hours. -22- Model T31681 (Mfd. Since 12/19)
⁄ " throat. 10 TPI blade. serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to our website or latest catalog for additional recommended accessories. Food-Grade Replacement Blade, ⁄...
Cover machine with a clean, dry cloth until and require no maintenance throughout their next use. lifespan. Monthly Check • Under normal conditions, replace saw blade after sawing 4400 lbs. of meat or bone. -24- Model T31681 (Mfd. Since 12/19)
4. Adjust feet to stabilize machine (Page 13). 4. Feet not adjusted properly. 5. Replace blade (Page 16). 5. Blade weld at fault/teeth broken. 6. Motor bearings at fault. 6. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. -25- Model T31681 (Mfd. Since 12/19)
Page 28
5. Adjust blade tracking (Page 17). 5. Blade tracking is incorrect. Material difficult to 1. Material built up on table. 1. Clean and sanitize table, then apply a thin coat of move across table. food-grade lubricant (Page 20). -26- Model T31681 (Mfd. Since 12/19)
Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -27- Model T31681 (Mfd. Since 12/19)
Page 30
Neutral current at the time of printing, but it may not match your machine. 110VAC Always use the wiring diagram 5-15 Plug inside the motor junction box. Ground READ ELECTRICAL SAFETY -28- Model T31681 (Mfd Since 12/19) ON PAGE 27!
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
Page 33
MOTOR 750W 110V 1-PH W/CAPACITOR PT31681077 FLAT HD SCR M5-.8 X 12 43-1 PT31681043-1 MOTOR FAN COVER PT31681078 STRAIN RELIEF TYPE-2 11MM BUY PARTS ONLINE AT GRIZZLY.COM! -31- Model T31681 (Mfd. Since 12/19) Scan QR code to visit our Parts Store.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -32- Model T31681 (Mfd.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.