Selectype Menu Map; Printing A Status Check - Epson Stylus Pro 7000 Series Product Information

Message/Light Explanation
Paper slipped and fed
PAPER NOT
/ into the printer at an
STRAIGHT
light angle.
Paper Out
flashing
/ No paper is loaded.
PAPER OUT
light
Paper Out
Paper ran out.
on
/ Paper could not be
RELOAD PAPER
light reversed into the
Paper Out
on printing position.
Image is too wide for
the paper loaded in the
printer.
Paper is not fully
ejected.
PAPER NOT CUT
was cleared.
/ Paper is too thick for
REMOVE PAPER
light print head cleaning.
Paper Out
on
SECURE PAPER Paper set lever was
released.
LEVER/Paper Out
light on
An error has occurred.
SERVICE REQ.
<error number> /
All lights flashing
The waste ink system is
SERVICE REQ.
00000100/ full.
All lights flashing
TURN PWR OFF This message appears
AND ON
after you clear a paper
jam.
You tried to print a test
UNABLE TO
PRINT
pattern while an error
condition was present.
Response
Reload paper, making
sure the edges are
straight and aligned with
both rows of holes.
Load paper.
Remove any printouts or
paper remaining in the
printer and load more
paper.
If the message appears
during a print job, reset
the printer by pressing
the button for 3
Pause
seconds. Then load
paper and resend the
job.
Remove the paper.
Reload it so that the
right and bottom edges
are straight and aligned
with both rows of holes.
Resize your image or
load wider paper.
Cut the paper at the
paper insertion slot, then
reload paper.
error Reload paper.
Push the paper set lever
down to remove the
paper. Print head
cleaning automatically
starts. After cleaning,
reload paper.
Pull the paper set lever
all the way up. Restart
print job for best results.
Note the error number,
and turn the printer off
and then on. If the
message remains,
contact EPSON.
Contact EPSON for
service.
Turn the printer off and
then on again.
After 3 seconds, the
message disappears.
Press the button
Pause
to exit SelecType mode.
If the message appears
again, clear the error
before you print.
EPSON Stylus Pro 7000 series

SelecType Menu Map

The following illustration shows the SelecType
with the settings available for each one.
PRINTER SETTING
MENU:
PLATEN GAP
PAGE LINE
INTERFACE
PARA. I/F
CODE PAGE
PAPER SIZE CHECK ROLL MARG
PAPER ALIGN CHK
INIT. PANEL
ROLL MARG
INIT. PANEL
READY
HEAD ALIGNMENT
MENU:
PAPER THICK.
ADJUST. PATT.
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
#12

Printing a Status Check

The status check shows the current default settings, amount of
ink remaining in each cartridge, page count, and the status of
various printer parts.
Follow these steps to print the status check:
1. Load a sheet of paper in the printer. (You can print test
pages on roll paper, but you will use more paper.)
2. Press the
SelecType
repeatedly until you see
display.
3. Press the button until you see
Item
on the display.
CHECK=PRINT
8/00
™ menus, along
PRINTER STATUS
TEST PRINT MENU:
NOZZLE CHECK
VERSION
STATUS CHECK
INK LEFT-K
INK LEFT-C
INK LEFT-M
INK LEFT-LC
INK LEFT-LM
INK LEFT-Y
CUTTER LIFE
TOTAL PRINTS
WASTE INK
CR MOTOR
PF MOTOR
HEAD UNIT
CLEANER
CUTTER REPLACE PAPER CONFIG.
MENU:
PAPER NUMBER
CUT. REPLACE
OPEN LOWER COVER THICK. PAT.
REPLACE CUTTER PAPER THICK. NO.
SUCTION
DRYING TIME
CLOSE LOWER COVER
button on the control panel. Press it
on the
TEST PRINT MENU
STATUS
EPSON Stylus Pro 7000 series - 7
MENU:
MENU: