Siemens MKB-1 Installation Instructions

Installation Instructions
Model MKB-1
Annunciator/Keypad Module
The SIEMENS Model MKB-1 Annunciator
communicates with the MMB-1 Main Control
Board through the System network link. The
MKB-1 provides the MXL with its primary control
and annunciation.
OPERATION
The MKB-1 has an 80 character, backlit LCD
alphanumeric display that continuously updates
information about the System status and user
defined device messages (See Figure 1). If there
are multiple alarms, and/or troubles, including
supervisories and security conditions, the MKB-1
displays the highest priority event that occurred.
The user can see additional alarm and trouble
data by pressing the NEXT key. Press the HOLD
key at any time to stop the display from scrolling.
There are switches for acknowledging fire alarms
(ALARM ACK), silencing audibles (AUD SIL),
acknowledging supervisories (SUPV ACK),
System troubles (TRBL ACK), and security
conditions (SEC ACK). There is also a separate
key for resetting the Control Panel (RESET).
The 10 digit numeric keypad allows entry of the
three levels of user passwords. It also performs
specific menu driven operations as well as
programming and maintenance functions.
Another series of switches located on the MKB-1
allows the user access to the MXL Control menu.
There are also System status indicator LEDs.
The ALARM and TROUBLE LEDs function even
if the main processor fails (See Figure 1).
Siemens Building Technologies, Inc.
8 Fernwood Road
Florham Park, New Jersey 07932
P/N 315-090856-6
INSTALLATION
Always remove all power before installation.
Unpack the MKB-1. Inspect the module for such
things as integrated circuits (ICs) not firmly
seated in their sockets, bent IC pins, connectors
not properly installed, dirt, and packing material
on the board.
Setting the Network Address
(See Figure 2)
1 . Before installing the MKB-1 panel, set the
network address on S1, the switch on the
ANN-1 board located on the back of the
MKB-1. Use dipswitches SW1 and SW2 on
switch Sl to set the network address of the
MKB-1.
2. The MKB-1 module address is always set
within network addresses 248 through 251.
Set the individual switches as follows:
NOTE: Switches S1-SW3 and S1-SW4 are for
future use. The use of switch S1-SW5 is
described below.
A
S W T I C H
2 4 8
S 1 S - W 1 O p e n - O F F C o l
S 1 S - W 2 O p e n - O F F O
S 1 S - W 3 C o l e s d - O N C o l
S 1 S - W 4 C o l e s d - O N C o l
S 1 S - W 5 C o l e s d - O N C o l
3. One supervised MKB-1 must be installed at
network address 251. Other supervised
MKBs may be at the other addresses.
Siemens Building Technologies, Ltd.
2 Kenview Boulevard
Brampton, Ontario L6T 5E4 CN
Fire Safety
D D R E S S E S S E T F O : R
2 4 9 2 5 0
e s d - O N O p e n - O F F C o l
p e n - O F F C o l e s d - O N C o l
e s d - O N C o l e s d - O N C o l
e s d - O N C o l e s d - O N C o l
e s d - O N C o l e s d - O N C o l
2 5 1
e s d - O N
e s d - O N
e s d - O N
e s d - O N
e s d - O N