Related Manuals for Bush Hog SM 60
Summary of Contents for Bush Hog SM 60
- Page 1 All manuals and user guides at all-guides.com BUSH HOG ® Model SM 60 Side Mount Rotary Cutter Operator’s Manual OPERATION l l MAINTENANCE 1007 $4.00 97701...
- Page 2 If your manual should become lost or destroyed, Bush Hog will be glad to provide you with a new copy. Order from Bush Hog, P. O. Box 1039, Selma, Alabama 36702-1039. Most of our manuals can also be downloaded from our website at www.bushhog.com.
-
Page 3: Table Of Contents
It is the Retail Customer’s responsibility to deliver the product to the authorized Bush Hog Dealer, from whom he purchased it, for service or replacement of defective parts which are covered by warranty. Repairs to be submitted for warranty consideration must be made within forty-five (45) days of failure. -
Page 4: Warranty
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judge- ment of Bush Hog such use affects its performance, stability or reliability. -
Page 5: Dealer Preparation Check List
For Non-Agricultural use, OSHA, ASAE, SAE and ANSI standards require the use of Chain Guards or other protective guards at all times. Bush Hog strongly recommends the use of such guards for Agricultural uses as well, to reduce the risk of property damage, serious bodily injury or even death from objects thrown out by or from contact with the cutting blades. - Page 6 All manuals and user guides at all-guides.com IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice.
-
Page 7: Safety Precautions
All manuals and user guides at all-guides.com IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. -
Page 8: Federal Laws And Regulations
All manuals and user guides at all-guides.com IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. -
Page 9: Introduction & Description
It is to be used on tractors weighing 1-1 INTRODUCTION a minimum of 6000 lbs. (2722 kg) not including We are pleased to have you as a Bush Hog cus- ballast and having a minimum of 50 PTO horse- tomer. Your Side Mount Rotary Cutter, Model power. -
Page 10: Preparation For Use
All manuals and user guides at all-guides.com Fig. 1-2 Hydraulic Circuit (Cast Iron Pump & Motor) Motor Filter 1102 RPM at 10 Micron 540 RPM with 15 PSI Bypass Relief Valve 3200 PSI Suction Strainer SECTION II PREPARATION FOR USE 2-1 MOUNTING CUTTER ON TRACTOR A. -
Page 11: Driveline Modification
All manuals and user guides at all-guides.com Fig. 2-3 Pivot Linkage F. Pull driveline apart. Attach the outer (female) section to the tractor PTO shaft and the inner (male) section to the pump input shaft. Pull on each drive- line section to make sure yokes lock into place. G. -
Page 12: Operating Procedures
All manuals and user guides at all-guides.com G. Repeat steps “E” and “F” to other driveline sec- section. Reassemble driveline and attach to tractor tion. and implement. Pull on driveline section to make H. De-burr the ends of the drivelines and clean sure yokes lock into place. -
Page 13: Reversing Blade Rotation
All manuals and user guides at all-guides.com WARNING WARNING ALL ROTARY CUTTERS HAVE THE ABILITY TO KEEP CLEAR OF MACHINE WHEN RAISING DISCHARGE OBJECTS AT HIGH SPEEDS, AND LOWERING THE CUTTER HEAD. WHICH COULD RESULT IN SERIOUS INJURY TO BYSTANDERS OR PASSERS-BY. D. -
Page 14: Storage
All per paragraph 4-6. Always replace both blades bolts should be torqued as recommended in Table 4- with a match pair. Use only genuine Bush Hog 2 unless otherwise indicated. replacement parts. 9. Make certain chains and/or side bands are in... -
Page 15: Recommended Hydraulic Oil
All manuals and user guides at all-guides.com Figure 4-1 Lubrication Replace Yearly Check Before Each Use 40 Hours 40 Hours 40 Hours 150 Hours Figure 4-2 Driveline Universal Joint Before Each Use 20 Hours To Remove Yoke Shield: Press all three tabs with screwdriver and slide cover back. -
Page 16: Blade Holder Removal
A. Remove hydraulic pressure and return lines deck. Blades should only be replaced in matched from connections on motor. pairs. Use only genuine Bush Hog replacements B. Remove hydraulic fittings from both sides of parts. motor. -
Page 17: Troubleshooting
All manuals and user guides at all-guides.com Figure 4-4 Hydraulic Motor Return Line Hose Pressure LIne Hydraulic Fittings Spindle Housing Motor contamination such as pump failure. This requires D. Turn motor 180º. Reinstall bolts retaining motor removal and individual flushing and cleaning of all to spindle housing. - Page 18 Check condition of pump shaft seal. Pump worn or damaged Overhaul or replace. 2. Hydraulic fluid Pressure too high Contact authorized Bush Hog dealer. overheated Fluid dirty or fluid level low Clean or replace filter and strainer. Add fluid (above 200º F [93ºC]) bring up to bottom of filler strainer.
-
Page 19: Dealer Assembly
14. Before operating the machine, read the maintenance section of this manual to be sure that any parts requiring lubrication such as gearboxes are full to avoid any possible damage. BEFORE OPERATING THE EQUIPMENT, IF YOU HAVE ANY QUESTIONS REGARDING THE PROPER ASSEMBLY OR OPERATION, CONTACT YOUR AUTHORIZED BUSH HOG DEALER OR REPRESENTATIVE. -
Page 20: Basic Machine Assembly
All manuals and user guides at all-guides.com roll pins. It may be necessary to remove cylinder 5-1 BASIC MACHINE ASSEMBLY port caps to extend cylinder. With port caps CAUTON removed, watch out for oil spraying out of cylinder ports. BASE UNIT IS EXTREMELY TOP E. -
Page 21: Optional Safety Chain Installation
All manuals and user guides at all-guides.com CAUTON Figure 5-3 Side Band USE OF THIS MACHINE ON TOO SMALL A TRACTOR CAN CAUSE TRACTOR UPSET. DO NOT USE THIS MACHINE ON A TRACTOR WEIGHING LESS THAN 6000 LBS. (2722 kg), NOT INCLUDING BALLAST. -
Page 22: Optional Tailwheel Installation
All manuals and user guides at all-guides.com 5-5 OPTIONAL TAILWHEEL Figure 5-6 Tailwheel Assembly INSTALLATION Apply Decal A. Position mounting bracket against underside of frame as shown. (Fig. 5-6) B. Position mounting plate on top side of frame and fasten with four 5/8 x 7-1/2” bolts and locknuts. C. -
Page 23: Safety Decal
To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information. - Page 24 All manuals and user guides at all-guides.com SAFETY DECALS CONTINUED 83374 83373 83377 82617 83375...
-
Page 25: Torque Specifications
All manuals and user guides at all-guides.com TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* AMERICAN B O L T D IA M E T E R Bolt Head Markings W R E N C H (IN .) “B ”... - Page 26 All manuals and user guides at all-guides.com P.O. Box 1039 Selma, AL 36702-1039 Telephone (334) 874-2700 www.bushhog.com...