GE ZKD910 Installation Instructions Manual
Hide thumbs
Also See for ZKD910:
- Owner's manual (16 pages) ,
- Installation instructions manual (16 pages) ,
- Owner's manual (16 pages)
Related Manuals for GE ZKD910
Summary of Contents for GE ZKD910
- Page 1 ® GE Monogram Warming Drawer Installation Instructions 27" Wide Models: ZKD910 30" Wide Models: ZTD910...
-
Page 2: Table Of Contents
This appliance must be properly grounded. See “Electrical Supply”, page 4. CAUTION WARNING If you have a question concerning the installa- WARNING tion of this product, call the GE Answer ® Center Consumer Information Service at ANTI-TIP PRECAUTIONS 800.626.2000, 24 hours a day, 7 days a week. -
Page 3: Models Available
Design Information Warming Drawer The warming drawers may be installed ZTD910 Models directly into a wall or wall oven cabinetry, 30” Wide model Available or below a countertop. ZKD910 27” Wide model Product 27" 23-1/4" Dimensions Drawer 10-1/2" 9" Open 1"... -
Page 4: Advance Planning
Design Information Warming Drawer • The drawer may be installed below a Advance • Electrical power cord is located on the right countertop, a cooktop, a single or double side of the warming oven. Locate the outlet Planning oven and side by side using 2 drawers. within reach of the 56”... -
Page 5: Remove The Packaging And Parts
Installation Preparation Warming Drawer Parts provided: • Place carton on a flat surface. Remove • 4 Wood Screws • Open one end of the carton and lift off the Packaging top piece. • Lift the warmer up and out of the carton. and Parts •... -
Page 6: Installation Below Wall Ovens
Design Information Warming Drawer 23-1/2" Min. Additional clearance between Note: Installation Inside cutouts may be required. Check to be Below sure that oven supports above the Warming Drawer location does not Wall Ovens obstruct the required interior 23-1/2” depth and 9-1/4” height. INSTALLATION BELOW A Oven... -
Page 7: Step 1: Provide Cabinet Support And Anti-Tip Bracket
Installation Warming Drawer 2"x 4" or 2"x 4" or Provide Equivalent Runners Equivalent Runners Cabinet Support 23-1/2" 23-1/2" 22" 25" 27" 30" • The warmer drawer may be supported by When installed below a single or double oven, Important: either a solid bottom, 2 x 4 or 2 x 2 run- check to be sure that any oven supports above the cutout do not ners. -
Page 8: Zxd27B, Zxd30B For Installation Of A Custom Panel
ZXD27B, ZXD30B Accessory Installation of a Custom Panel Tool and Materials required: This kit contains a mounting panel to support • Phillips screwdriver a trimless custom drawer front up to 3/4” • Drill and appropriate bits thick. A custom handle of your choice, must be (Brad point recommended for drilling through installed on the new panel. - Page 9 ZXD27B, ZXD30B Accessory Installation of a Custom Panel STEP 4: 1/4" Secure custom panel to metal mounting panel • Lay the custom panel, appearance side down, on a 3/16" clean surface. • Place the flat side of the metal panel onto the back side 1/4"...
-
Page 10: Jxpn1 Pan Kit
JXPN1 Accessory Pan Kit for Warming Drawer This kit contains supports and pans to fit your 27" new Warming Drawer. Models This kit is designed to fit both 27” and 30” wide models. Select the parts for your model and discard the parts that do not fit. 30"... - Page 11 JXPN1 Accessory Pan Kit for Warming Drawer 7. Arrange pans to suit food storage needs. Combinations with full size pan Combinations without full size pan. 8. Discard the Side to side rails and filler panel not used. Important Notes: • Use the pan lids to keep foods moist. •...
- Page 12 To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night. For Monogram local ser vice in your area, call 1-800-444-1845.