Introduction This will inform you of the information you need to know before using this product, such as an overview of the OS equipped with the preinstalled model, the overall configuration of this manual, the various manuals associated with this product, and so on. —...
1. About the Product Windows 10 IoT Enterprise 2019 LTSC, equipped with the preinstalled model, is the OS for embedded applications. CONTEC’s preinstalled models perform customization to build the OS based on a configuration determined in advance. In this manual you will find basic information on the installed OS, as well as explanations of setup procedures and recovery procedures.
Reference Manual Read this when This describes the hardware Download from operating the product. aspects such as functions the Contec and settings. website (PDF) Pre-installed Model Must read this after This explains basic OS Download from OS Manual (This manual) opening the package.
— — Introduction BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 3. Manual composition This manual is composed as follows: — 7 —...
The copyright, patent right or any other intellectual property right pertaining to the Software or any documentary attachments, such as manuals, as well as any copies thereof (the “Software and the Like”) shall belong to CONTEC, and customers shall have no rights therefor other than those expressly authorized herein.
Page 9
BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) Article 6. Termination 1.CONTEC may terminate the Agreement with immediate effect without any notice or demand to the customer if the customer fails to comply with any of the provisions herein.
Notes Regarding Use This manual explains the precautions for using the product safely. Please make sure to read this before using this product. — 10 —...
— — Notes Regarding Use BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 1. Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely.
Even when using the product continuously, be sure to read the manual in the CONTEC’s website and understand the contents. Do not modify the software. CONTEC will bear no responsibility for any problems, etc., resulting from modifying the software.
— — Notes Regarding Use BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 3. About Adobe Flash Player Adobe Flash Player is disabled by default. You may require a license from Adobe Systems Incorporated or the partner of Adobe.to use the service.
— — Notes Regarding Use BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 4. About Unified Write Filter Unified Write Filter function (referred to as “UWF” in this document) is the new filtering which combined EWF, FBWF, and Registry filter. UWF has deterred the write to DISK by redirecting the write to DISK from operating system or application to overlay.
Page 15
— — Notes Regarding Use BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) In early stages, a UWF overlay region serves as maximum size of 1024 MB. The present operating condition of a UWF overlay region can be checked by the following command.
— — Notes Regarding Use BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 5. Security Warning When connecting to the network, be aware of security-related problems. See the examples of Security measures below and set up the product properly along with the network devices. 1.
Setup procedures This manual describes the setup procedure that a user needs to perform after unpacking the product with a pre-installed operation system. The setup of Windows is performed interactively. — 17 —...
— — Setup procedures BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 1. Windows setup Check that the monitor, the keyboard and the mouse are connected with the PC. Do not connect other devices until a Windows setup is completed. After confirming the connections, turn on the PC power.
Page 19
— — Setup procedures BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) Select your home region. And, click the Select keyboard layout. And, click the Select additional keyboard layout. If not, click the Skip It is a document regarding License. Click the Accept —...
Page 20
— — Setup procedures BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) Then, the display of creating account can be viewed. Enter the account name to be used. Click the Next Then, the display of creating password can be viewed.
Page 21
— — Setup procedures BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 10. When a password setting is skipped, an automatic logon can be made by the created account (user name). — 21 —...
Update Version:11.0.105(KB4480965) Windows Media Player 12.0.17763.292 Microsoft .NET Framework 4.7.2 Remote Desktop Connection 10.0.17763 Remote Desktop Protocol 10.6 CONTEC utilities CONTEC Manager 4.0.1 TPBK(S) Supply schedule Mainstream support end date 2024/01/09 Extended support end date 2029/01/09 End of Life 2028/11/30 —...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 2. Storage and Partition Configuration The following is for a 2.5” HDD model with 100 GB * The disk usage indicated is a reference value. — 24 —...
Page 25
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) The following is for a 2.5” SDD model with 256 GB * The disk usage indicated is a reference value. — 25 —...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 3. Programs and Features 1. Installed software View a list of installed software 2. Installed updates View a list of installed updates. — 26 —...
Internet to perform setup, or recover the preinstalled model. Under CONTEC preinstalled model factory default settings, Device Lockdown is enabled. Using the lockdown function, you can restrict unintentional user operations or control information displayed on the screen.
4. UWF settings For UWF settings, use either the Microsoft console application UWF manager (uwfmgr.exe) or CONTEC Manager, the GUI application installed in the preinstalled model. The UWF function’s filter is disabled by default. The following explains the procedure for checking the UWF settings using UWF manager (uwfmgr.exe).
Page 29
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) When UWF is enabled, writing to the disk will be restricted, allowing for the lifetime of disks with writing restrictions to be lengthened. It also allows you to prevent unintentional system alterations. Below is a configuration graph of the UWF functions.
Page 30
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) Input “uwfmgrget-config” and press the [Enter] key. View current setting status. Enter the Item Display Meaning command Filter state Disabling the Enabling the Check the state Volume state Un-protected Invalid Volume...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 4. Main device drivers Category Data IDE ATA/ATAPI Controller Display Adapter Intel Core i5 model Intel Celeron model — 31 —...
Page 32
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) Network Adapter Sound video and game controller System devices — 32 —...
Page 33
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) Universal Serial Bus Controller — 33 —...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 5. Set to factory default values This section explains the preinstalled model’s various factory default settings. You can reset these settings unless their values are specially designated. 1.
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 2. Ethernet settings The preinstalled model’s product Ethernet display and the OS Ethernet recognition status are shown below. Product Ethernet display OS Ethernet recognition LAN A Ethernet LAN B Ethernet 2...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) [Internet Protocol Version 6] IP address : automatically DNS : automatically 3. Serial Port Settings The preinstalled model’s product SERIAL display and OS SERIAL recognition status are shown below. Product SERIAL display OS SERIAL recognition SERIAL A...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 4. Optional power settings This section explains the factory settings for power options. Power and sleep button settings When I press the power button : Shut down Shutdown settings Turn on fast startup(recommended) : Off Advanced settings...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 6. Changing the language The preinstalled model supports English, Japanese, Korean and Simplified Chinese. The following explains how to manually change the language settings. As an example we will explain the procedure for switching from English to Japanese.
Page 39
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) Input “JAPAN” in the textbox, and a list will appear below. Select [日本語 (Japanese)], and then click [Next]. The language function’s installation screen will be displayed, but it is already installed. Click [Install].
Page 40
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) In order to change the display language during startup and shutdown to Japanese, you also need to perform the following settings. In Control Panel, click [時計と地域 (Clock and Region)], then click [地域...
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 7. Windows Update You can install the correction program (QFE) in [Update & Security]. On the [Start] menu, click [Settings]. Click [Update & Security]. — 41 —...
CONTEC provides not only functions installed with this product such as the RAS function to secure reliability and the UWF function providing the OS, but also setting tools that allow you to use CONTEC products more smoothly and a library to control the functions listed below.
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 3. Properties screen *The following images may differ from the actual product. Monitor hardware status such as the CPU temperature, the M/B temperature and so on. If it exceeds the set threshold, the set alarm action will be activated.
— — System Information BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 4. UWF settings The following explains the method for setting write protection for the C drive. ① Click [ ] and set to [ ② Tick the volume [C] targeted for protection. ①...
— — Recovery Method BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 1. Preparations This document describes the recovery procedures in a case where OS becomes unable to start up on a preinstalled-OS system. The Recovery uses USB connection’s DVD-ROM Drive. Please prepare a necessary equipment according to DVD-ROM used.
— — Recovery Method BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 2. Procedure Before performing the operation, connect the monitor, USB keyboard, USB mouse and USB DVD- ROM drive to the product. 1. BIOS settings Please set recovery media (Disc 1 of 2) to a USB DVD-ROM drive, and connect with PC. Turn on the power supply of PC and Press [DEL] key or [ESC] key immediately after turning on the power, activating Aptio Setup Utility.
(If you do not continue the recovery, press N key.) HDD/SSD initialization and recovery CImage Tool for Windows processing will be performed automatically. Copyright<C> 2017 CONTEC CO., LTD. Version X.X.X.X Copy swm file: xxxxx.swm [xx%] copied The screen on the left will appear. Take out the CImage Tool for Windows Copyright<C>...
— — Recovery Method BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 3. BIOS settings After restarting the system by the method outlined above, immediately press [DEL] or [ESC] to start the BIOS settings screen (Aptio Setup Utility). Press the [→] key to select the “Advanced”...
— — Recovery Method BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 4. Start OS The screen of the left figure is displayed after several times reboot. Perform Windows setup following the setup procedure in this manual. — 53 —...
— Customer Support and Inquiry BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) 1. Services CONTEC offers the useful information including product manuals that can be downloaded through the Contec website. Download https://www.contec.com/download/ You can download updated driver software, firmware, and differential manuals in several languages.
Page 56
No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this document.
Page 57
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan https://www.contec.com/ No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. BX-M1000 Pre-installed Model OS Manual(Windows 10 IoT Enterprise 2019 LTSC) NA06617 (LYWU591)