Operation And Use; Brightness Of The Display; Timer Function - DeLonghi HCX Series Instructions For Use Manual

a. The appliance must not be located directly beneath
a current outlet.
b. The plug and outlet must be easy to reach after in-
stallation.
c. No electric cables or other pipes could be damaged
during the installation.
d. Keep away from curtains or flammable materials.
To wall-mount, proceed as follows:
Turn the appliance upside down on a flat stable surface . Using a
screwdriver, fix the 2 brackets (H) with the 2 screws (I) as shown
in Fig. 2. For brick walls use a 6 mm concrete drill bit . For plaster
board or false (hollow) walls, it is recommended to use appropri-
ate screws and anchors (not supplied).
1. Before drilling the wall, mark the exact points, respecting
the minimum distances as shown in fig. 3.
2. Drill the wall where previously marked, and insert the plas-
tic anchors (K).
3. Fix the 2 metal brackets (H) using the two screws (J) provid-
ed.
4. Hang the appliance on the bracket.
5. Mark out the 2 lower fixing points. Remove the appliance,
drill the lower holes and insert the wall anchors (K).
6. Now, you can hang back the heater on the bracket and
fix the lower part of the appliance with the 2 remaining
screws (J).
USE

Operation and use

- Plug into the mains socket.
- The appliance emits a beep. The power indicator light (A)
comes on and remains lit while the appliance is powered.
- The appliance switches to stand-by.
- Press the ON/STAND-BY (B) to turn the appliance on. It be-
gins heating the room according to the current settings.
- Press the MODE (D) button to select one of the following
operating modes:
- Freeze prevention
In this mode, the appliance keeps the room at a tempera-
ture of 7°C to avoid freezing.
Heating 1, 2, 3 and Heating 3 + Fan
-
In this mode, the desired temperature can be selected by
pressing the adjustment buttons + and –. By pushing the
+ or - button once, the temperature (shown on the display)
will increase or decrease by 1°C.
Heating 1
The appliance operates at low power.
Heating 2
The appliance operates at medium power.
Heating 3
The appliance operates at high power.
Heating 3 + Fan
The appliance operates at the maximum power with the
fan. The setting temperature range available is from 16°C
to 32°C.
"ECO plus" function
The "ECO plus" function is available in Heating 1, 2 3 and 3 +
fan modes only. To activate the function, press the "ECO plus" (E)
button. When this function is active the appliance automatically
sets the most appropriate power level to guarantee optimum
comfort while reducing energy consumption.
While the "ECO plus" function is active, the appliance may switch
automatically to a lower heating power than the one displayed.
Working indicator
The symbol indicates the heating status by means of its
colors.
RED: the unit is heating at the maximum power.
YELLOW: the unit is heating at the medium power.
GREEN: the unit is heating at the minimum power.
absent: the unit is not heating.

Brightness of the display

The appliance allows two different brightness settings for the
display. The highest is active when any key button is pressed.
After a few seconds of keyboard inactivity, the brightness will
decrease to the operating brightness level.
Key lock
In order to avoid accidental operation, you can lock the key-
board using the keylock function. To activate this function press
buttons + and - (C) together for at least 3 seconds. The display
shows the symbol and a double acoustic signal will be emit-
ted. To deactivate the function proceed in the same way.

Timer function

This function can be activated in two different ways.
Delayed start: With the appliance on-standby, press the timer
button (F) . The
with the hours left before the appliance comes on. Change the
hours using the + and - (C) buttons, then wait a few seconds
for the program to be stored. The display will return to off and
the symbols remains on. When the programmed time has
elapsed, the appliance will come on with the previous settings.
5
symbol is displayed flashing together